Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback
Identifieur interne : 000635 ( Pmc/Checkpoint ); précédent : 000634; suivant : 000636Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback
Auteurs : F. Ganet [France] ; M. Q. Le [France] ; J. F. Capsal [France] ; P. Lermusiaux [France] ; L. Petit [France] ; A. Millon [France] ; P. J. Cottinet [France]Source :
- Scientific Reports [ 2045-2322 ] ; 2015.
Abstract
The development of steerable guide wire or catheter designs has been strongly limited by the lack of enabling actuator technologies. This paper presents the properties of an electrostrive actuator technology for steerable actuation. By carefully tailoring material properties and the actuator design, which can be integrated in devices, this technology should realistically make it possible to obtain a steerable guide wire design with considerable latitude. Electromechanical characteristics are described, and their impact on a steerable design is discussed.
Url:
DOI: 10.1038/srep18593
PubMed: 26673883
PubMed Central: 4682083
Affiliations:
Links toward previous steps (curation, corpus...)
Links to Exploration step
PMC:4682083Le document en format XML
<record><TEI><teiHeader><fileDesc><titleStmt><title xml:lang="en">Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback</title>
<author><name sortKey="Ganet, F" sort="Ganet, F" uniqKey="Ganet F" first="F." last="Ganet">F. Ganet</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a2"><institution>Pulsalys</institution>
, 47 Boulevard du 11 Novembre 1918, CS 90170, 69625 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Le, M Q" sort="Le, M Q" uniqKey="Le M" first="M. Q." last="Le">M. Q. Le</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Capsal, J F" sort="Capsal, J F" uniqKey="Capsal J" first="J. F." last="Capsal">J. F. Capsal</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Lermusiaux, P" sort="Lermusiaux, P" uniqKey="Lermusiaux P" first="P." last="Lermusiaux">P. Lermusiaux</name>
<affiliation wicri:level="1"><nlm:aff id="a3"><institution>Groupement Hospitalier Edouard Herriot - Chirurgie Vasculaire</institution>
– Pav. M –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a4"><institution>Université de Lyon – Université Claude Bernard Lyon 1</institution>
, 8 Avenue Rockefeller Lyon –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Petit, L" sort="Petit, L" uniqKey="Petit L" first="L." last="Petit">L. Petit</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Millon, A" sort="Millon, A" uniqKey="Millon A" first="A." last="Millon">A. Millon</name>
<affiliation wicri:level="1"><nlm:aff id="a3"><institution>Groupement Hospitalier Edouard Herriot - Chirurgie Vasculaire</institution>
– Pav. M –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a4"><institution>Université de Lyon – Université Claude Bernard Lyon 1</institution>
, 8 Avenue Rockefeller Lyon –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Cottinet, P J" sort="Cottinet, P J" uniqKey="Cottinet P" first="P. J." last="Cottinet">P. J. Cottinet</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
</titleStmt>
<publicationStmt><idno type="wicri:source">PMC</idno>
<idno type="pmid">26673883</idno>
<idno type="pmc">4682083</idno>
<idno type="url">http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4682083</idno>
<idno type="RBID">PMC:4682083</idno>
<idno type="doi">10.1038/srep18593</idno>
<date when="2015">2015</date>
<idno type="wicri:Area/Pmc/Corpus">000645</idno>
<idno type="wicri:Area/Pmc/Curation">000645</idno>
<idno type="wicri:Area/Pmc/Checkpoint">000635</idno>
</publicationStmt>
<sourceDesc><biblStruct><analytic><title xml:lang="en" level="a" type="main">Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback</title>
<author><name sortKey="Ganet, F" sort="Ganet, F" uniqKey="Ganet F" first="F." last="Ganet">F. Ganet</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a2"><institution>Pulsalys</institution>
, 47 Boulevard du 11 Novembre 1918, CS 90170, 69625 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Le, M Q" sort="Le, M Q" uniqKey="Le M" first="M. Q." last="Le">M. Q. Le</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Capsal, J F" sort="Capsal, J F" uniqKey="Capsal J" first="J. F." last="Capsal">J. F. Capsal</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Lermusiaux, P" sort="Lermusiaux, P" uniqKey="Lermusiaux P" first="P." last="Lermusiaux">P. Lermusiaux</name>
<affiliation wicri:level="1"><nlm:aff id="a3"><institution>Groupement Hospitalier Edouard Herriot - Chirurgie Vasculaire</institution>
– Pav. M –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a4"><institution>Université de Lyon – Université Claude Bernard Lyon 1</institution>
, 8 Avenue Rockefeller Lyon –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Petit, L" sort="Petit, L" uniqKey="Petit L" first="L." last="Petit">L. Petit</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Millon, A" sort="Millon, A" uniqKey="Millon A" first="A." last="Millon">A. Millon</name>
<affiliation wicri:level="1"><nlm:aff id="a3"><institution>Groupement Hospitalier Edouard Herriot - Chirurgie Vasculaire</institution>
– Pav. M –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
<affiliation wicri:level="1"><nlm:aff id="a4"><institution>Université de Lyon – Université Claude Bernard Lyon 1</institution>
, 8 Avenue Rockefeller Lyon –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
<author><name sortKey="Cottinet, P J" sort="Cottinet, P J" uniqKey="Cottinet P" first="P. J." last="Cottinet">P. J. Cottinet</name>
<affiliation wicri:level="1"><nlm:aff id="a1"><institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</nlm:aff>
<country xml:lang="fr">France</country>
<wicri:regionArea># see nlm:aff country strict</wicri:regionArea>
</affiliation>
</author>
</analytic>
<series><title level="j">Scientific Reports</title>
<idno type="eISSN">2045-2322</idno>
<imprint><date when="2015">2015</date>
</imprint>
</series>
</biblStruct>
</sourceDesc>
</fileDesc>
<profileDesc><textClass></textClass>
</profileDesc>
</teiHeader>
<front><div type="abstract" xml:lang="en"><p>The development of steerable guide wire or catheter designs has been strongly limited by the lack of enabling actuator technologies. This paper presents the properties of an electrostrive actuator technology for steerable actuation. By carefully tailoring material properties and the actuator design, which can be integrated in devices, this technology should realistically make it possible to obtain a steerable guide wire design with considerable latitude. Electromechanical characteristics are described, and their impact on a steerable design is discussed.</p>
</div>
</front>
<back><div1 type="bibliography"><listBibl><biblStruct><analytic><author><name sortKey="Ederle, J" uniqKey="Ederle J">J. Ederle</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Qureshi, A I" uniqKey="Qureshi A">A. I. Qureshi</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Razavi, M K" uniqKey="Razavi M">M. K. Razavi</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Saeed, M" uniqKey="Saeed M">M. Saeed</name>
</author>
<author><name sortKey="Hetts, S W" uniqKey="Hetts S">S. W. Hetts</name>
</author>
<author><name sortKey="English, J" uniqKey="English J">J. English</name>
</author>
<author><name sortKey="Wilson, M" uniqKey="Wilson M">M. Wilson</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Losey, A D" uniqKey="Losey A">A. D. Losey</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Hetts, S W" uniqKey="Hetts S">S. W. Hetts</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Fu, Y" uniqKey="Fu Y">Y. Fu</name>
</author>
<author><name sortKey="Liu, H" uniqKey="Liu H">H. Liu</name>
</author>
<author><name sortKey="Huang, W" uniqKey="Huang W">W. Huang</name>
</author>
<author><name sortKey="Wang, S" uniqKey="Wang S">S. Wang</name>
</author>
<author><name sortKey="Liang, Z" uniqKey="Liang Z">Z. Liang</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Roberts, T P L" uniqKey="Roberts T">T. P. L. Roberts</name>
</author>
<author><name sortKey="Hassenzahl, W V" uniqKey="Hassenzahl W">W. V. Hassenzahl</name>
</author>
<author><name sortKey="Hetts, S W" uniqKey="Hetts S">S. W. Hetts</name>
</author>
<author><name sortKey="Arenson, R L" uniqKey="Arenson R">R. L. Arenson</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Settecase, F" uniqKey="Settecase F">F. Settecase</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Gomes, P" uniqKey="Gomes P">P. Gomes</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Liu, C" uniqKey="Liu C">C. Liu</name>
</author>
<author><name sortKey="Qin, H" uniqKey="Qin H">H. Qin</name>
</author>
<author><name sortKey="Mather, P T" uniqKey="Mather P">P. T. Mather</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Buckley, P R" uniqKey="Buckley P">P. R. Buckley</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Rousseau, I A" uniqKey="Rousseau I">I. A. Rousseau</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Miles, R R" uniqKey="Miles R">R. R. Miles</name>
</author>
<author><name sortKey="Schumann, D L" uniqKey="Schumann D">D. L. Schumann</name>
</author>
<author><name sortKey="Pearson, M A" uniqKey="Pearson M">M. A. Pearson</name>
</author>
<author><name sortKey="Hilken, D" uniqKey="Hilken D">D. Hilken</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Guo, S" uniqKey="Guo S">S. Guo</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Guo, S" uniqKey="Guo S">S. Guo</name>
</author>
<author><name sortKey="Nakamura, T" uniqKey="Nakamura T">T. Nakamura</name>
</author>
<author><name sortKey="Fukuda, T" uniqKey="Fukuda T">T. Fukuda</name>
</author>
<author><name sortKey="Oguro, K" uniqKey="Oguro K">K. Oguro</name>
</author>
<author><name sortKey="Negoro, M" uniqKey="Negoro M">M. Negoro</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Sewa, S" uniqKey="Sewa S">S. Sewa</name>
</author>
<author><name sortKey="Onishi, K" uniqKey="Onishi K">K. Onishi</name>
</author>
<author><name sortKey="Asaka, K" uniqKey="Asaka K">K. Asaka</name>
</author>
<author><name sortKey="Fujiwara, N" uniqKey="Fujiwara N">N. Fujiwara</name>
</author>
<author><name sortKey="Oguro, K" uniqKey="Oguro K">K. Oguro</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Daneshvar, E D" uniqKey="Daneshvar E">E. D. Daneshvar</name>
</author>
<author><name sortKey="Smela, E" uniqKey="Smela E">E. Smela</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Bauer, F" uniqKey="Bauer F">F. Bauer</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Choi, S T" uniqKey="Choi S">S. T. Choi</name>
</author>
<author><name sortKey="Kwon, J O" uniqKey="Kwon J">J. O. Kwon</name>
</author>
<author><name sortKey="Bauer, F" uniqKey="Bauer F">F. Bauer</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Capsal, J F" uniqKey="Capsal J">J.-F. Capsal</name>
</author>
<author><name sortKey="Galineau, J" uniqKey="Galineau J">J. Galineau</name>
</author>
<author><name sortKey="Le, M Q" uniqKey="Le M">M.-Q. Le</name>
</author>
<author><name sortKey="Domingues Dos Santos, F" uniqKey="Domingues Dos Santos F">F. Domingues Dos Santos</name>
</author>
<author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Capsal, J F" uniqKey="Capsal J">J.-F. Capsal</name>
</author>
<author><name sortKey="Galineau, J" uniqKey="Galineau J">J. Galineau</name>
</author>
<author><name sortKey="Lallart, M" uniqKey="Lallart M">M. Lallart</name>
</author>
<author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
<author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Capsal, J F" uniqKey="Capsal J">J.-F. Capsal</name>
</author>
<author><name sortKey="Dantras, E" uniqKey="Dantras E">E. Dantras</name>
</author>
<author><name sortKey="Lacabanne, C" uniqKey="Lacabanne C">C. Lacabanne</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Le, M Q" uniqKey="Le M">M. Q. Le</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Ganet, F" uniqKey="Ganet F">F. Ganet</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Nordon, I M" uniqKey="Nordon I">I. M. Nordon</name>
</author>
<author><name sortKey="Hinchliffe, R J" uniqKey="Hinchliffe R">R. J. Hinchliffe</name>
</author>
<author><name sortKey="Holt, P J" uniqKey="Holt P">P. J. Holt</name>
</author>
<author><name sortKey="Loftus, I M" uniqKey="Loftus I">I. M. Loftus</name>
</author>
<author><name sortKey="Thompson, M M" uniqKey="Thompson M">M. M. Thompson</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Hutchins, G M" uniqKey="Hutchins G">G. M. Hutchins</name>
</author>
<author><name sortKey="Miner, M M" uniqKey="Miner M">M. M. Miner</name>
</author>
<author><name sortKey="Boitnott, J K" uniqKey="Boitnott J">J. K. Boitnott</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Breedveld, P" uniqKey="Breedveld P">P. Breedveld</name>
</author>
<author><name sortKey="Sheltes, J S" uniqKey="Sheltes J">J. S. Sheltes</name>
</author>
<author><name sortKey="Blom, E M" uniqKey="Blom E">E. M. Blom</name>
</author>
<author><name sortKey="Verheij, J E I" uniqKey="Verheij J">J. E. I. Verheij</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Willey, D G" uniqKey="Willey D">D. G. Willey</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Petit, L" uniqKey="Petit L">L. Petit</name>
</author>
<author><name sortKey="Guiffard, B" uniqKey="Guiffard B">B. Guiffard</name>
</author>
<author><name sortKey="Seveyrat, L" uniqKey="Seveyrat L">L. Seveyrat</name>
</author>
<author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Lallart, M" uniqKey="Lallart M">M. Lallart</name>
</author>
<author><name sortKey="Capsal, J F" uniqKey="Capsal J">J.-F. Capsal</name>
</author>
<author><name sortKey="Sebald, G" uniqKey="Sebald G">G. Sebald</name>
</author>
<author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
<author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Huang, C" uniqKey="Huang C">C. Huang</name>
</author>
<author><name sortKey="Zhang, Q" uniqKey="Zhang Q">Q. Zhang</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Song, Y" uniqKey="Song Y">Y. Song</name>
</author>
<author><name sortKey="Guan, Z" uniqKey="Guan Z">Z. Guan</name>
</author>
<author><name sortKey="Nie, Y" uniqKey="Nie Y">Y. Nie</name>
</author>
<author><name sortKey="Guan, X" uniqKey="Guan X">X. Guan</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
<author><name sortKey="Yuse, K" uniqKey="Yuse K">K. Yuse</name>
</author>
<author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
<author><name sortKey="Kanda, M" uniqKey="Kanda M">M. Kanda</name>
</author>
<author><name sortKey="Lebrun, L" uniqKey="Lebrun L">L. Lebrun</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
<author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
<author><name sortKey="Guiffard, B" uniqKey="Guiffard B">B. Guiffard</name>
</author>
<author><name sortKey="Lebrun, L" uniqKey="Lebrun L">L. Lebrun</name>
</author>
<author><name sortKey="Putson, C" uniqKey="Putson C">C. Putson</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Calvert, P" uniqKey="Calvert P">P. Calvert</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Liu, Y" uniqKey="Liu Y">Y. Liu</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Le, Q M" uniqKey="Le Q">Q. M. Le</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Shennib, H" uniqKey="Shennib H">H. Shennib</name>
</author>
<author><name sortKey="Bastawisy, A" uniqKey="Bastawisy A">A. Bastawisy</name>
</author>
<author><name sortKey="Mack, M J" uniqKey="Mack M">M. J. Mack</name>
</author>
<author><name sortKey="Moll, F H" uniqKey="Moll F">F. H. Moll</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Stephenson, E R" uniqKey="Stephenson E">E. R. Stephenson</name>
</author>
<author><name sortKey="Sankholkar, S" uniqKey="Sankholkar S">S. Sankholkar</name>
</author>
<author><name sortKey="Ducko, C T" uniqKey="Ducko C">C. T. Ducko</name>
</author>
<author><name sortKey="Damiano, R J" uniqKey="Damiano R">R. J. Damiano</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Sanchez, L A" uniqKey="Sanchez L">L. A. Sanchez</name>
</author>
<author><name sortKey="Le, M Q" uniqKey="Le M">M. Q. Le</name>
</author>
<author><name sortKey="Rabenorosoa, K" uniqKey="Rabenorosoa K">K. Rabenorosoa</name>
</author>
<author><name sortKey="Liu, C" uniqKey="Liu C">C. Liu</name>
</author>
<author><name sortKey="Zemiti, N" uniqKey="Zemiti N">N. Zemiti</name>
</author>
<author><name sortKey="Poignet, P" uniqKey="Poignet P">P. Poignet</name>
</author>
<author><name sortKey="Dombre, E" uniqKey="Dombre E">E. Dombre</name>
</author>
<author><name sortKey="Menciassi, A" uniqKey="Menciassi A">A. Menciassi</name>
</author>
<author><name sortKey="Dario, P" uniqKey="Dario P">P. Dario</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Lallart, M" uniqKey="Lallart M">M. Lallart</name>
</author>
<author><name sortKey="Cottinet, P J" uniqKey="Cottinet P">P.-J. Cottinet</name>
</author>
<author><name sortKey="Guyomar, D" uniqKey="Guyomar D">D. Guyomar</name>
</author>
<author><name sortKey="Lebrun, L" uniqKey="Lebrun L">L. Lebrun</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Capsal, J F" uniqKey="Capsal J">J.-F. Capsal</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Belhora, F" uniqKey="Belhora F">F. Belhora</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Faraz, A" uniqKey="Faraz A">A. Faraz</name>
</author>
<author><name sortKey="Payandeh, S" uniqKey="Payandeh S">S. Payandeh</name>
</author>
</analytic>
</biblStruct>
</listBibl>
</div1>
</back>
</TEI>
<pmc article-type="research-article"><pmc-dir>properties open_access</pmc-dir>
<front><journal-meta><journal-id journal-id-type="nlm-ta">Sci Rep</journal-id>
<journal-id journal-id-type="iso-abbrev">Sci Rep</journal-id>
<journal-title-group><journal-title>Scientific Reports</journal-title>
</journal-title-group>
<issn pub-type="epub">2045-2322</issn>
<publisher><publisher-name>Nature Publishing Group</publisher-name>
</publisher>
</journal-meta>
<article-meta><article-id pub-id-type="pmid">26673883</article-id>
<article-id pub-id-type="pmc">4682083</article-id>
<article-id pub-id-type="pii">srep18593</article-id>
<article-id pub-id-type="doi">10.1038/srep18593</article-id>
<article-categories><subj-group subj-group-type="heading"><subject>Article</subject>
</subj-group>
</article-categories>
<title-group><article-title>Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback</article-title>
</title-group>
<contrib-group><contrib contrib-type="author"><name><surname>Ganet</surname>
<given-names>F.</given-names>
</name>
<xref ref-type="aff" rid="a1">1</xref>
<xref ref-type="aff" rid="a2">2</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Le</surname>
<given-names>M. Q.</given-names>
</name>
<xref ref-type="aff" rid="a1">1</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Capsal</surname>
<given-names>J. F.</given-names>
</name>
<xref ref-type="aff" rid="a1">1</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Lermusiaux</surname>
<given-names>P.</given-names>
</name>
<xref ref-type="aff" rid="a3">3</xref>
<xref ref-type="aff" rid="a4">4</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Petit</surname>
<given-names>L.</given-names>
</name>
<xref ref-type="aff" rid="a1">1</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Millon</surname>
<given-names>A.</given-names>
</name>
<xref ref-type="aff" rid="a3">3</xref>
<xref ref-type="aff" rid="a4">4</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Cottinet</surname>
<given-names>P. J.</given-names>
</name>
<xref ref-type="corresp" rid="c1">a</xref>
<xref ref-type="aff" rid="a1">1</xref>
</contrib>
<aff id="a1"><label>1</label>
<institution>Université de Lyon - INSA de Lyon – LGEF</institution>
, 8 rue de la Physique, 69 621 Villeurbanne –<country>France</country>
</aff>
<aff id="a2"><label>2</label>
<institution>Pulsalys</institution>
, 47 Boulevard du 11 Novembre 1918, CS 90170, 69625 Villeurbanne –<country>France</country>
</aff>
<aff id="a3"><label>3</label>
<institution>Groupement Hospitalier Edouard Herriot - Chirurgie Vasculaire</institution>
– Pav. M –<country>France</country>
</aff>
<aff id="a4"><label>4</label>
<institution>Université de Lyon – Université Claude Bernard Lyon 1</institution>
, 8 Avenue Rockefeller Lyon –<country>France</country>
</aff>
</contrib-group>
<author-notes><corresp id="c1"><label>a</label>
<email>pierre-jean.cottinet@insa-lyon.fr</email>
</corresp>
</author-notes>
<pub-date pub-type="epub"><day>17</day>
<month>12</month>
<year>2015</year>
</pub-date>
<pub-date pub-type="collection"><year>2015</year>
</pub-date>
<volume>5</volume>
<elocation-id>18593</elocation-id>
<history><date date-type="received"><day>04</day>
<month>08</month>
<year>2015</year>
</date>
<date date-type="accepted"><day>20</day>
<month>11</month>
<year>2015</year>
</date>
</history>
<permissions><copyright-statement>Copyright © 2015, Macmillan Publishers Limited</copyright-statement>
<copyright-year>2015</copyright-year>
<copyright-holder>Macmillan Publishers Limited</copyright-holder>
<license license-type="open-access" xlink:href="http://creativecommons.org/licenses/by/4.0/"><pmc-comment>author-paid</pmc-comment>
<license-p>This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit <ext-link ext-link-type="uri" xlink:href="http://creativecommons.org/licenses/by/4.0/">http://creativecommons.org/licenses/by/4.0/</ext-link>
</license-p>
</license>
</permissions>
<abstract><p>The development of steerable guide wire or catheter designs has been strongly limited by the lack of enabling actuator technologies. This paper presents the properties of an electrostrive actuator technology for steerable actuation. By carefully tailoring material properties and the actuator design, which can be integrated in devices, this technology should realistically make it possible to obtain a steerable guide wire design with considerable latitude. Electromechanical characteristics are described, and their impact on a steerable design is discussed.</p>
</abstract>
</article-meta>
</front>
<body><p>Image-guided endovascular interventions have gained in popularity in clinical practice as studies have consistently shown that these minimally invasive interventions are of equivalent or greater efficiency and offer lower mortality rates when compared to traditional open surgical techniques<xref ref-type="bibr" rid="b1">1</xref>
<xref ref-type="bibr" rid="b2">2</xref>
<xref ref-type="bibr" rid="b3">3</xref>
. A majority of interventions involve the use of flexible guide wires and catheters that are guided by the surgeon into the appropriate vessels under real-time X-ray imaging<xref ref-type="bibr" rid="b4">4</xref>
<xref ref-type="bibr" rid="b5">5</xref>
<xref ref-type="bibr" rid="b6">6</xref>
. Maneuverability of a guide wire for intravascular navigation is the key to reaching the targeted area; the ability to steer a guide wire thus affects to a great extent the duration and success of the procedure. The difficulty of steering and controlling the guide wire increases the risks for complications, including vascular dissection, perforation, and thrombosis<xref ref-type="bibr" rid="b7">7</xref>
. Some of these risks can be offset by systemic heparinization, which is routinely used in clinical endovascular procedures performed today, though this may itself increase the risk of procedural hemorrhage.</p>
<p>For many procedures the guide wire is guided from a safe entrance vessel (e.g., the common femoral artery) to a target that is relatively far away in the body via branched or tortuous vessels<xref ref-type="bibr" rid="b7">7</xref>
. With a traditional guide wire, its tip is steered by manually rotating the wire about its axis and pushing it forward into the desired vessel. After the guide wire has been navigated through several vascular turns, the torque at the proximal end is hindered<xref ref-type="bibr" rid="b7">7</xref>
<xref ref-type="bibr" rid="b8">8</xref>
. Moreover, it is difficult to manipulate a guide wire tip through sharp turns, for instance when entering a recurrent branch vessel whose origin is directed at an orientation greater than 90 degrees to the parent vessel<xref ref-type="bibr" rid="b9">9</xref>
.</p>
<p>With these evident challenges, various guidance mechanisms for guide wire and catheter navigation have been designed and are in clinical use. Manual and pullwire guidance were the first to be used. Guide wires for manual direction are flexible, small-diameter wires placed through the patent lumens of catheters and are manually navigated into branch vessels before the functional catheter tip to serve as a stable track for the catheter to follow<xref ref-type="bibr" rid="b10">10</xref>
. Manually controlled, shapeable, metallic guide wires of variable stiffness placed through variably stiff plastic catheters have been the mainstay of endovascular catheter guidance under X-ray fluoroscopic imaging for decades, and the number of guide wires and catheters available for specific applications throughout the body is huge<xref ref-type="bibr" rid="b7">7</xref>
<xref ref-type="bibr" rid="b10">10</xref>
.</p>
<p>Smart material actuators provide an alternative to the classical mechanisms of guidance. Shape memory polymers (SMPs) have during the past 10 years been investigated for this purpose. Direct heat is the most commonly used trigger for an SMP to resume its original shape, although ultraviolet and infrared radiation, electrical current, pH changes, and magnetic fields have also been used<xref ref-type="bibr" rid="b11">11</xref>
. In a study by Buckley <italic>et al.</italic>
, inductive heating was used to induce a change in SMP shape by loading ferromagnetic particles into the polymer and exposing it to an alternating magnetic field, as could be used in conjunction with MRI<xref ref-type="bibr" rid="b12">12</xref>
. Shape memory alloys (SMAs) are better studied than SMPs and have a shorter response time, but also a higher density, higher cost, and lower attainable strains<xref ref-type="bibr" rid="b13">13</xref>
.</p>
<p>A shape memory alloy actuated catheter has been designed such that tubes of the SMA were distributed about the central axis of the catheter and could be heated to achieve bending due to shrinking of the SMA material<xref ref-type="bibr" rid="b7">7</xref>
. When the heating stops, the material is naturally cooled and reforms its original shape<xref ref-type="bibr" rid="b7">7</xref>
. Some major considerations when it comes to these methods include safe heating, efficient cooling, the use of many lead wires if the catheter assumes a multi-link style and a complex position control due to the hysteresis<xref ref-type="bibr" rid="b13">13</xref>
. Hydraulic systems have also been investigated; for example, Miles patented a pneumatic or hydraulic catheter design in which tubing runs on either side of a catheter to an elastomeric cylinder<xref ref-type="bibr" rid="b14">14</xref>
. However, the size of such devices makes them complex when it comes to their future utilization with Minimally Invasive Methods (MIS) of surgery.</p>
<p>Ionic Polymer Composite (IPMC) actuators have also been suggested for the design of active catheters or guide wires<xref ref-type="bibr" rid="b15">15</xref>
<xref ref-type="bibr" rid="b16">16</xref>
<xref ref-type="bibr" rid="b17">17</xref>
. These actuators can generate large displacements at relatively low electrical field and moderate speed; however, their manufacturing process is often relatively expensive and additional energy is usually consumed in order to hold the actuator in position<xref ref-type="bibr" rid="b18">18</xref>
. Electrostrictive polymer actuators, especially poly(vinylidene fluoride-trifluoroethylene-chlorotrifluoroethylene), namely terpolymer P(VDF-TrFE-CTFE), have shown attractive properties, which make them promising for extensive employment in active guide wire applications<xref ref-type="bibr" rid="b19">19</xref>
. Some of their characteristics include a high energy density, ease of fabrication, and a relatively high strain<xref ref-type="bibr" rid="b20">20</xref>
. However, in order to generate large deformations, electrostrictive polymers require very high electrical fields which block the development of steerable guide wire. Recently, a novel approach enabling to drastically improve the mechanical energy density of an electrostrictive polymer at low electrical fields has been investigated in<xref ref-type="bibr" rid="b21">21</xref>
<xref ref-type="bibr" rid="b22">22</xref>
. This should make it possible to overcome this technological issue.</p>
<p>Recently, Capsal <italic>et al.</italic>
proposed a simple and efficient solution to improve the electromechanical performances of the P(VDF-TrFE-CTFE) fluorinated terpolymer by reducing the required electric field<xref ref-type="bibr" rid="b22">22</xref>
. The results demonstrated that a doping of the polymer with bis(2-ethylhexyl) phthalate (DEHP) plasticizer leads to improved molecular mobility and large Maxwell Wagner Sillars interfacial polarization effects, resulting in decrease Young modulus as well as increase dielectric permittivity of the material<xref ref-type="bibr" rid="b23">23</xref>
. Hence, choosing an adequate polymer matrix/plasticizer combination would enable the generation of large macroscopic dipoles combined with phase heterogeneities while reducing the Young’s modulus of the polymer and increasing its dielectric permittivity.</p>
<p>As a result of the improved dielectric permittivity and the decreased Young modulus, a great enhancement of the low-frequency electrostrictive transverse strain (a twenty-eight-fold increase compared to the neat fluorinated-polymer at 10 V/μm) was achieved. More importantly, compared to traditional composites, the developed plasticizer-polymers exhibited a decreased dielectric breakdown strength which is very important for practical actuator applications<xref ref-type="bibr" rid="b24">24</xref>
<xref ref-type="bibr" rid="b25">25</xref>
. Consequently, the approach proposed herein, using a low-cost plasticizer bis(2-ethylhexyl) phthalate (DEHP), is promising for the development of new all-organic composites with excellent electrostrictive properties for steerable guide wires.</p>
<p>The present paper is divided into four parts. The first part is dedicated to the requirements and working principal of steerable guide wires. The second presents the material properties and the elaboration of devices used in this work. The third part concerns the medialization of the “smart” guide wire, using finite element modeling. Finally, the last part is dedicated to the analysis of the results.</p>
<sec disp-level="1"><title>Requirements and Working Principals</title>
<p>The requirements for actuators to be used for “smart” guide wires can be very broad. However, the major performances to take into account when designing remotely steerable guide wires are the bending angles achievable by the guide wire, the time to obtain bending, the degree of rotation that can be achieved, and the capacity for miniaturization of the design<xref ref-type="bibr" rid="b26">26</xref>
. The design of the guide wire shaft is a significant factor in determining the formation of curves, the angles of deflection and the levels of steerability. The choice of material determines the level of pushability, torque and flexibility and can be manipulated along the length of the guide wire through a variety of means to achieve the desired results. The objective of this study was to demonstrate the possibility of using an electroactive polymer for a steerable guide wire, and the overriding constraints were related to the following points<xref ref-type="bibr" rid="b26">26</xref>
:<list id="l1" list-type="bullet"><list-item><p>Typical angle in human vessels.</p>
</list-item>
<list-item><p>Time response.</p>
</list-item>
</list>
</p>
<p>Hutchins <italic>et al.</italic>
realized a study on the typical curvature and angle in human vessels<xref ref-type="bibr" rid="b27">27</xref>
. Measurements were made of parent and branch vessel diameters and of the included angles of branch-points from postmortem human coronary arteries. The results demonstrate no relationship between the branch-angle and the vessel caliber. The included angle between branches varied from 32 degrees to 124 degrees regardless of the relative or absolute vessel calibers. It was hence necessary to develop “smart” wire guides able to generate these bending angle values. Moreover, it is interesting to note that most medical device suppliers propose catheters or guide wires that have been pre-bent between 30° and 120° <xref ref-type="bibr" rid="b28">28</xref>
.</p>
<p>The time response of the actuator is directly linked to the physical property of the surgeon, since the “smart” guide wire is controlled by the surgeon as illustrated in <xref ref-type="fig" rid="f1">Fig. 1</xref>
. The typical reaction time of humans is about 180 ms<xref ref-type="bibr" rid="b29">29</xref>
. Two effects contribute to this delay. The first is the time that elapses between photons arriving at the retina and the surgeons perceiving that the guide wire is not in a good position (in other words, the time delay in human vision). The second is the time that elapses between nerve impulses leaving the brain and movement in the muscles. There is another delay concerning the electronic control of the guide wire (10 ms), so typically it is necessary that the time response of the actuator does not exceed 100 ms. It is easy to understand this value since visualizing the guide wire tip while navigating vessels is important in order to avoid that the guide wire tip is undesirably forced through a vessel or tissue, causing perforation. Consequently, the time response of the actuator needs to be lower than the time response of the surgeon.</p>
<p>Although the traditional robotic actuators which are currently used in robotic surgical devices, such as electro-magnetic drives and hydraulic/pneumatic machines, have all been extensively investigated and have advanced performances which can, in some aspects, surpass that of humans, they simply do not have the capabilities and diversity required to meet the demand for new actuation systems in the proposed application. They are stiff, noncompliant and mechanically complex, which makes scalability and miniaturization difficult. To meet the technical requirements, electrostrictive polymers could be used for solid-state actuators. They can be realized by sandwiching a polymer dielectric layer between electrodes. When applying an electrical field to the electrodes, the dielectric material contracts due to electrostatic forces and expands in the lateral directions.</p>
<p>This work has focused on the modeling, design and realization of a cylindrical guide wire with two degrees of freedom (DOF). The 2-DOF functionality was achieved by uniquely sectored electrodes on the surface of a cylindrical electrostrictive polymer as illustrated in <xref ref-type="fig" rid="f2">Fig. 2</xref>
. Such a design allows the smart guide wire to bend in both directions. In fact, there exists a quadratic relationship between the strain and the electrical field; hence, the generated displacement is independent of the sign of the electrical field. If an electrical field is applied between the central electrode and electrode 1, the polymer is, due to the electrostatic force, compressed in the thickness direction, causing the structure to bend. If the electrical field is applied between the central electrode and electrode 2, the smart catheter bends in the opposite direction.</p>
</sec>
<sec disp-level="1"><title>Modeling of the Structure</title>
<p>In view of the architecture of the actuator, an analytical approach was deemed too complex for modeling the electromechanical behavior of the “smart” guide wire. Therefore, finite element modeling was chosen. The multi-physics finite element model was developed using Ansys. This tool is used to model the basic physics occurring within an electrostrictive polymer. The models are developed to track the geometric variation of the electroactive polymer in the presence of an electrical field. These variations of geometries are then correlated to a mechanical generated stress<xref ref-type="bibr" rid="b30">30</xref>
.</p>
<p>To produce this model, the geometry of the “smart” guide wire was idealized as a perfect circle with constant electrode shapes. These geometries were created using the built-in Ansys tools. The use of these built-in geometry tools made it possible to input the dimensions as Ansys parameters and easily adjust them throughout the modeling process. To create the three-dimensional shape, a two-dimensional electroactive polymer cross-section was drawn and then extruded to create the length of the guide wire.</p>
<p>The mesh was defined on the face of the EAP and then extended along the length of the EAP. It was designed to be fine near the electrode polymer interface which was accomplished using a distribution boundary condition. This condition guaranteed that the number of elements in this critical region remained constant even when the whole size in the middle was varied. The region was considered critical since it was where the largest changes in concentration were seen.</p>
<p>To perform the simulation, two physics packages were simultaneously used: electro-statics, and solid mechanics<xref ref-type="bibr" rid="b30">30</xref>
. The electro-statics analysis focuses on the input of the electrical field to the EAP, and this physics package is governed by Poisson’s law. The last physics package used in the simulation was the structural mechanics model. The bending in the tube-type EAP was modeled using a linear elastic model. The simulation parameters can be seen in <xref ref-type="table" rid="t1">Table 1</xref>
. Two compositions of the electroactive polymer were used, a neat terpolymer and a modified terpolymer; the data was extracted from the literature<xref ref-type="bibr" rid="b22">22</xref>
and is presented in <xref ref-type="table" rid="t2">Table 2</xref>
.</p>
<p>For the first simulation, an electrical field of 30 V/μm was applied between electrode 1 and the central electrode. The electric potential in the cross-section of the EAP is show in <xref ref-type="fig" rid="f3">Fig. 3</xref>
. The electrical field spread across the EAP in a symmetric manner between the central electrode and electrode 1. Due to geometric inconsistencies in the real sample, this is not always the case. The electrical field between electrode 2 and the central electrode appeared to be null, which was logical since no electrical field was applied. This electrode configuration allows a sectoring of the electrical field distribution in the structure. This was necessary for the development of a steerable guide wire.</p>
<p>The second set of simulations that were realized concerned the electromechanical activities of the “smart” guide wire. The simulation showed that the strain occurring mainly in the section near the base of the electrical field was the highest, and therefore corresponded to the electrostatic force. A comparison between the different compositions of the electroactive polymer under a constant electrical field of 30 V/μm is presented in <xref ref-type="fig" rid="f4">Fig. 4</xref>
The advantage of using an all-organic composite is clearly demonstrated in the simulation, where the generated bending angle was higher than for the neat polymer. An electrical field six times higher will be needed to obtain the same strain for a pure polymer, which corresponds to the dielectric breakdown of the materials<xref ref-type="bibr" rid="b21">21</xref>
. <xref ref-type="fig" rid="f5">Figure 5</xref>
shows the generated displacement along the length of the guide wire, for different electrical fields and when the electrical excitation is applied to electrode 1 or 2. The simulation demonstrates the possibility to generate displacement in both directions, when the electrode has been sectorized.</p>
</sec>
<sec disp-level="1"><title>Materials and Characterization</title>
<p>The validity of the proposed design was investigated using a prototype guide wire developed to explore control and sensing approaches for use in medical procedures, especially for cardiac applications. The prototype of the “smart” guide wire was designed to achieve a workspace sufficient for this application.</p>
<p>In this study, a fluorinated terpolymer P(VDF-TrFE-CTFE) was used due to its high mechanical energy density. However, a large electrical field was needed (E > 150 V/μm) in order to reach sufficient strain levels (>2%)<xref ref-type="bibr" rid="b19">19</xref>
, as is demonstrated by the simulation. The major drawback of electrostrictive polymers lies in the high electrical fields required. On the one hand, high electrical fields can be achieved at low voltages if the films are thin. On the other hand, the electromechanical transduction properties of any electrostrictive polymers are intrinsically regulated by the dielectric permittivity and Young modulus, Y, of the material<xref ref-type="bibr" rid="b31">31</xref>
. These parameters directly control both the achievable active stresses and strains. In order to increase the dielectric permittivity of polymer materials, different methods have been developed. The main approach is based on the dispersion of filler in the polymer matrix. However, one of the typical drawbacks of the composite approach lies in a substantial decrease of the material’s dielectric strength (<italic>E</italic>
<sub><italic>break</italic>
</sub>
)<xref ref-type="bibr" rid="b32">32</xref>
.</p>
<p>The architecture of the “smart” guide wire can be described as a tube, and can thus be realized by extrusion. Commercially available terpolymer products do not comprise a plasticizer. In order to extrude an all-organic composite tube, a terpolymer with plasticizer was thus fabricated using a solution casting method. First, a glass plate was covered with a film of lecithin dissolved in cyclohexane (5 w/w% solution). A doctor blade (Elcometer) was then employed to create a film with a thickness typically between 80 μm and 180 μm. After drying at room temperature, the film was heated during 1 h at 70 °C to ensure complete evaporation of the solvent. Then, the film was cut in small pieces of 5 × 5 mm<sup>2</sup>
. The tubings were extruded through a Laboratory Mixing Extruder (LME, Dynisco, Inc.) with a 0.476 cm outer die (o.d.) head and a 0.3175 cm mandrel tip at a mandrel temperature of 150 °C and a die temperature of 130 °C at 180 RPM. Next, the tube was cut into the desired length and recrystallized in an oven at the onset of the melting peak determined by a Setaram EVO 131 Dynamic Scanning Calorimetry (DSC). To realize a sufficient strain with the applicable voltages (lower than 10 kV), the thickness of the polymer had to be in the range of a few hundred microns. <xref ref-type="fig" rid="f6">Figure 6</xref>
shows a picture of an extruded tube of P(VDF-TrFE-CTFE) with 15%wt DEHP. According to previous works, the highest electrostrictive behavior was found in 15% wt. modified DEHP samples<xref ref-type="bibr" rid="b22">22</xref>
. Thus, this DEHP content was used in this study.</p>
<p>To evaluate the steerable properties of the fluorinated terpolymer films, a dedicated test setup, was built. On one side of the tube, a gold electrode was deposited by sputtering (Cressington 208 HR) through a mask. This made it possible to realize electrode 1 and 2. The inner electrode was created with the help of conductive grease. The sample was then connected to a commercially available guide wire in which an electric wire was manually integrated. The electric contact between the guide wire and the tube was assured with conductive glue.</p>
<p>The setup developed for characterizing the transverse vibration response of the polymer is shown schematically in <xref ref-type="fig" rid="f7">Fig. 7</xref>
. As seen in the <xref ref-type="fig" rid="f7">Fig. 7</xref>
, the “smart” guide wire to be tested was clamped in one end at a solid base (fixed) near the electric contact whereas the other end was free. When the polymer film was subjected to an electrical field, its expansion and contraction caused the free end of the tube to move and the movement was detected using an optical technique. In the current setup, a high-resolution camera was used to monitor the deflection (Canon 6D). The electrical field application was carried out with the Agilent 33220 A Function Generator and Treck power amplifier. All measurements were recorded in an open air environment (22 °C).</p>
</sec>
<sec disp-level="1"><title>Results and Discussion</title>
<p>In order to validate the design developed in Section 2, the electromechanical response was measured as a function of different stimuli.</p>
<sec disp-level="2"><title>Morphing</title>
<p>To demonstrate the device performances of the all-organic composites, several tube actuators were fabricated with different ratios between their length and outside diameter. <xref ref-type="fig" rid="f8">Figure 8</xref>
shows the measured curvature for an electrical field of 25 V/μm as a function of the length (L)/outer diameter (D<sub>outer</sub>
) ratio of the tube. It is interesting to note that the achievable curvature for a constant electrical field was higher when the length/diameter ratio was maximal. This dependence was logical since the global stiffness of the structure was lower when the ratio was high<xref ref-type="bibr" rid="b33">33</xref>
.</p>
<p><xref ref-type="fig" rid="f9">Figure 9</xref>
shows the bending angles generated as a function of a static electrical field at room temperature for a sample with a length of 65 mm, an inner diameter of 1 mm and an outer diameter of 1.4 mm. A quadratic dependence between the bending angles and the electrical field can be noted. This observation corresponds to the theory that shows such a dependence between the strain and the electrical field in electrostrictive materials<xref ref-type="bibr" rid="b34">34</xref>
<xref ref-type="bibr" rid="b35">35</xref>
. Moreover the bending angle produced by the proposed design corresponds to the typical angle available in the human body<xref ref-type="bibr" rid="b28">28</xref>
, making it possible to easily navigate the “smart” guide wire through the blood vessels. This function of steerability is relatively important to the development of the MIS procedure<xref ref-type="bibr" rid="b26">26</xref>
. To illustrate the generated displacement, pictures of the “smart” guide wire for two electrical fields are given in <xref ref-type="fig" rid="f10">Fig. 10</xref>
. It should be noted that the maximum electric filed used in experiment equal 50 V/μm resulting in a voltage of 10 kV cannot be considered to be safe for human body. A simple solution is to reduce the thickness of the electrostrictive material in order to significantly decrease the applied voltage. This can be achieved based on a multilayer structure consisting several thin electrostrictive polymers sandwiched between the electrodes. The multilayer architecture allows to considerably decrease the thickness of the whole actuator compared to the tube architecture. A fabrication of such multi-electrostrictive layers can be carried out using ink-jet printing technology<xref ref-type="bibr" rid="b36">36</xref>
. This aspect should be investigated in future work.</p>
<p><xref ref-type="fig" rid="f11">Figure 11</xref>
shows the step response of the prototype that was actuated by an electrical field of 20 V/μm. There were clearly two parts to the response. The fast part accounted for about 52% of the total measured bending angle. The slow part took about 100 ms to reach 90% of the total measured bending angle and was attributed to creep<xref ref-type="bibr" rid="b30">30</xref>
<xref ref-type="bibr" rid="b37">37</xref>
<xref ref-type="bibr" rid="b38">38</xref>
. The time response of the material was higher than for other electrostrictive polymer such as IPMC or conductive polymers with typical time responses above 2s<xref ref-type="bibr" rid="b39">39</xref>
. Moreover, the time response was compatible with the application since the reaction time for humans is about 180 ms as presented in section 2 (Requirements and working principles).</p>
</sec>
<sec disp-level="2"><title>Force feedback</title>
<p>A steerable property is not the only function requested for the development of a “smart” guide wire. For example, minimally invasive surgery operations are more and more often performed using a robot through small incisions<xref ref-type="bibr" rid="b40">40</xref>
. Force feedback is widely assumed to enhance performances in robotic surgery. However, current commercial robotic surgery systems provide no force feedback from the instruments, yet surgeons have demonstrated the ability to use these systems to perform delicate procedures such as coronary artery bypass grafting<xref ref-type="bibr" rid="b41">41</xref>
<xref ref-type="bibr" rid="b42">42</xref>
. Despite this demonstrated ability to work without force information, the dexterity with current minimally invasive instruments, whether manual or robotic, is clearly less than optimal. Furthermore, the implementation cost of force sensors that allow force feedback is prohibitive, due to the stringent design requirements imposed by the surgical environment<xref ref-type="bibr" rid="b43">43</xref>
.</p>
<p>Due to its unique properties, the P(VDF-TrFE-CTFE) composite employed to realize the “smart” guide wire can be used as a force sensor. In fact, by assuming a linear relationship between the electrical field I and the polarization (P = (ɛ− ɛ<sub>0</sub>
)E, where ɛ is the dielectric constant), it can be shown that the linearized constitutive equations for a pure electrostrictive material, i.e., without piezoelectric behavior, can be expressed using the Voigt notation<xref ref-type="bibr" rid="b31">31</xref>
<xref ref-type="bibr" rid="b44">44</xref>
according to</p>
<p><disp-formula id="eq1"><inline-graphic id="d33e429" xlink:href="srep18593-m1.jpg"></inline-graphic>
</disp-formula>
</p>
<p>where, S, T and D denote the total strain in the material, the stress component, and the electric displacement, respectively, <inline-formula id="d33e432"><inline-graphic id="d33e433" xlink:href="srep18593-m3.jpg"></inline-graphic>
</inline-formula>
is defined as the elastic compliance under constant stress and <italic>M</italic>
<sub><italic>31</italic>
</sub>
is the electrical field-related electrostrictive coefficient. It should be noted that the above assumption is fully valid for the investigated fluorinated terpolymer since a linear variation in the polarization versus electrical field magnitude up to 50 V/μm has been demonstrated<xref ref-type="bibr" rid="b45">45</xref>
.</p>
<p>As shown in Eq. <xref ref-type="disp-formula" rid="eq4">1</xref>
, electrostriction is generally defined as a quadratic coupling between the strain and the polarization. When working in sensor mode, the electrostrictive polymer is subjected to a DC-biased electrical field. Since the polymer is not piezoelectric, it is necessary to induce polarization with this DC bias in order to obtain a pseudo-piezoelectric behavior<xref ref-type="bibr" rid="b35">35</xref>
<xref ref-type="bibr" rid="b46">46</xref>
. The current induced by the mechanical stress can be expressed as:</p>
<p><disp-formula id="eq4"><inline-graphic id="d33e452" xlink:href="srep18593-m4.jpg"></inline-graphic>
</disp-formula>
</p>
<p>The product “2.M<sub>31</sub>
.E<sub>DC</sub>
” corresponds to the pseudo-piezoelectric coefficient. The generated current is proportional to the mechanical excitation, and it is thus possible to measure the force applied by the surgeon to the patient so as to obtain force feedback information.</p>
<p><xref ref-type="fig" rid="f12">Figure 12</xref>
displays the temporal evolution of the stress and the electrical response of an electrostrictive polymer, working in pseudo-piezoelectric mode (E<sub>DC</sub>
= 6 V/μm). The generated electrical charge and the force were in phase; in fact, the transported charge was the key governing the electromechanical conversion. It can be clearly seen in equation (Eq. <xref ref-type="disp-formula" rid="eq4">1</xref>
) since the electrical displacement was proportional to the time derivative of stress.</p>
<p><xref ref-type="fig" rid="f13">Figure 13</xref>
plots the electrical charge as a function of the force. The amount of transported charge was calculated by the time-integration of the measured current. A linear dependence between the electrical charge response and the mechanical force solicitation is clearly visible. This linear dependence exists theoretically as demonstrated in Eq. <xref ref-type="disp-formula" rid="eq4">2</xref>
.</p>
<p>The equivalent piezoelectric coefficient was provided to facilitate the comparison of the electromechanical activities of an electrostrictive material with a common piezoelectric material. It is related to the electrostrictive coefficient according to <italic>d</italic>
<sub><italic>31</italic>
</sub>
= <italic>2.M</italic>
<sub><italic>31</italic>
</sub>
.<italic>E</italic>
<sub><italic>DC</italic>
</sub>
. <xref ref-type="fig" rid="f14">Figure 14</xref>
gives the evolution of the piezoelectric coefficient as a function of the static electrical field (E<sub>DC</sub>
). One can see that all organic composites exhibited substantial piezoelectric coefficients equivalent to those of the piezoelectric ceramics for an electrical field lower than 10 V/μm. At this value of the electrical field, the neat polymer only had a piezoelectric coefficient equivalent to that of P(VDF-TrFE). These results demonstrate the pros of operating in pseudo-piezoelectric mode as this facilitates the design (same material for sensing and actuating) and the sensor sensitivity is equivalent to that of a piezoelectric ceramic. For example, a typical amplitude of force applied in the case of MIS is comprised between 1N and 10N<xref ref-type="bibr" rid="b47">47</xref>
, so the quantities of generated electrical charges are enough to be detected by the material for an electrical field of 1 V/μm.</p>
</sec>
</sec>
<sec disp-level="1"><title>Conclusion</title>
<p>This article presents the modeling and development of an electrostrictive tube for the steering and force feedback of a guide wire. An electrostrictive tube was desired to equip with the distal tip of a guide wire for endovascular navigation in order to reach the target regions inside blood vessels and through the tortuously curved pathways of blood vasculature. The proposed material is considered to be an excellent candidate for endovascular navigation thanks to its high flexibility and low current consumption. Furthermore, the developed electrostrictive polymer can be configured in both sensor and actuator modes, giving it a possibility of miniaturization to very small endovascular sizes. Such properties are extremely interesting for performing a multifunctional medical tool, especially in minimally invasive surgery where force or curvature sensor can be easily incorporated.</p>
<p>Future works focus on fabrication process of multi-electrostrive layers using ink-jet printing. This method allows to drastically decrease the material thickness, leading to enhanced electromechanical response under lower applied electric field. Another aspect of this work is to take into account the patient’s safety by choosing biocompatible plasticizes or adding a protection system into the catheter.</p>
</sec>
<sec disp-level="1"><title>Additional Information</title>
<p><bold>How to cite this article</bold>
: Ganet, F. <italic>et al.</italic>
Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback. <italic>Sci. Rep.</italic>
<bold>5</bold>
, 18593; doi: 10.1038/srep18593 (2015).</p>
</sec>
</body>
<back><ack><p>This research was supported by the company Pulsalys.</p>
</ack>
<ref-list><ref id="b1"><mixed-citation publication-type="journal"><name><surname>Ederle</surname>
<given-names>J.</given-names>
</name>
<italic>et al.</italic>
<article-title>Endovascular treatment with angioplasty or stenting versus endarterectomy in patients with carotid artery stenosis in the Carotid And Vertebral Artery Transluminal Angioplasty Study (CAVATAS): long-term follow-up of a randomised trial</article-title>
. <source>Lancet Neurol.</source>
<volume>8</volume>
, <fpage>898</fpage>
–<lpage>907</lpage>
(<year>2009</year>
).<pub-id pub-id-type="pmid">19717345</pub-id>
</mixed-citation>
</ref>
<ref id="b2"><mixed-citation publication-type="journal"><name><surname>Qureshi</surname>
<given-names>A. I.</given-names>
</name>
<article-title>Endovascular treatment of cerebrovascular diseases and intracranial neoplasms</article-title>
. <source>Lancet</source>
<volume>363</volume>
, <fpage>804</fpage>
–<lpage>813</lpage>
(<year>2004</year>
).<pub-id pub-id-type="pmid">15016492</pub-id>
</mixed-citation>
</ref>
<ref id="b3"><mixed-citation publication-type="journal"><name><surname>Razavi</surname>
<given-names>M. K.</given-names>
</name>
<italic>et al.</italic>
<article-title>Abdominal myomectomy versus uterine fibroid embolization in the treatment of symptomatic uterine leiomyomas</article-title>
. <source>AJR Am. J. Roentgenol.</source>
<volume>180</volume>
, <fpage>1571</fpage>
–<lpage>1575</lpage>
(<year>2003</year>
).<pub-id pub-id-type="pmid">12760922</pub-id>
</mixed-citation>
</ref>
<ref id="b4"><mixed-citation publication-type="journal"><name><surname>Saeed</surname>
<given-names>M.</given-names>
</name>
, <name><surname>Hetts</surname>
<given-names>S. W.</given-names>
</name>
, <name><surname>English</surname>
<given-names>J.</given-names>
</name>
& <name><surname>Wilson</surname>
<given-names>M.</given-names>
</name>
<article-title>MR fluoroscopy in vascular and cardiac interventions (review)</article-title>
. <source>Int. J. Cardiovasc. Imaging</source>
<volume>28</volume>
, <fpage>117</fpage>
–<lpage>137</lpage>
(<year>2012</year>
).<pub-id pub-id-type="pmid">21359519</pub-id>
</mixed-citation>
</ref>
<ref id="b5"><mixed-citation publication-type="journal"><name><surname>Losey</surname>
<given-names>A. D.</given-names>
</name>
<italic>et al.</italic>
<article-title>Magnetically Assisted Remote-controlled Endovascular Catheter for Interventional MR Imaging: <italic>In Vitro</italic>
Navigation at 1.5 T versus X-ray Fluoroscopy</article-title>
. <source>Radiology</source>
<volume>271</volume>
, <fpage>862</fpage>
–<lpage>869</lpage>
(<year>2014</year>
).<pub-id pub-id-type="pmid">24533872</pub-id>
</mixed-citation>
</ref>
<ref id="b6"><mixed-citation publication-type="journal"><name><surname>Hetts</surname>
<given-names>S. W.</given-names>
</name>
<italic>et al.</italic>
<article-title>Endovascular Catheter for Magnetic Navigation under MR Imaging Guidance: Evaluation of Safety <italic>In Vivo</italic>
at 1.5T</article-title>
. <source>Am. J. Neuroradiol.</source>
<volume>34</volume>
, <fpage>2083</fpage>
–<lpage>2091</lpage>
(<year>2013</year>
).<pub-id pub-id-type="pmid">23846795</pub-id>
</mixed-citation>
</ref>
<ref id="b7"><mixed-citation publication-type="journal"><name><surname>Fu</surname>
<given-names>Y.</given-names>
</name>
, <name><surname>Liu</surname>
<given-names>H.</given-names>
</name>
, <name><surname>Huang</surname>
<given-names>W.</given-names>
</name>
, <name><surname>Wang</surname>
<given-names>S.</given-names>
</name>
& <name><surname>Liang</surname>
<given-names>Z.</given-names>
</name>
<article-title>Steerable catheters in minimally invasive vascular surgery</article-title>
. <source>Int. J. Med. Robot.</source>
<volume>5</volume>
, <fpage>381</fpage>
–<lpage>391</lpage>
(<year>2009</year>
).<pub-id pub-id-type="pmid">19795440</pub-id>
</mixed-citation>
</ref>
<ref id="b8"><mixed-citation publication-type="journal"><name><surname>Roberts</surname>
<given-names>T. P. L.</given-names>
</name>
, <name><surname>Hassenzahl</surname>
<given-names>W. V.</given-names>
</name>
, <name><surname>Hetts</surname>
<given-names>S. W.</given-names>
</name>
& <name><surname>Arenson</surname>
<given-names>R. L.</given-names>
</name>
<article-title>Remote control of catheter tip deflection: an opportunity for interventional MRI</article-title>
. <source>Magn. Reson. Med. Off. J. Soc. Magn. Reson. Med. Soc. Magn. Reson. Med.</source>
<volume>48</volume>
, <fpage>1091</fpage>
–<lpage>1095</lpage>
(<year>2002</year>
).</mixed-citation>
</ref>
<ref id="b9"><mixed-citation publication-type="journal"><name><surname>Settecase</surname>
<given-names>F.</given-names>
</name>
<italic>et al.</italic>
<article-title>Magnetically-assisted remote control (MARC) steering of endovascular catheters for interventional MRI: A model for deflection and design implications</article-title>
. <source>Med. Phys.</source>
<volume>34</volume>
, <fpage>3135</fpage>
–<lpage>3142</lpage>
(<year>2007</year>
).<pub-id pub-id-type="pmid">17879774</pub-id>
</mixed-citation>
</ref>
<ref id="b10"><mixed-citation publication-type="journal"><name><surname>Gomes</surname>
<given-names>P.</given-names>
</name>
<source>Medical Robotics: Minimally Invasive Surgery.</source>
(Elsevier, <year>2012</year>
).</mixed-citation>
</ref>
<ref id="b11"><mixed-citation publication-type="journal"><name><surname>Liu</surname>
<given-names>C.</given-names>
</name>
, <name><surname>Qin</surname>
<given-names>H.</given-names>
</name>
& <name><surname>Mather</surname>
<given-names>P. T.</given-names>
</name>
<article-title>Review of progress in shape-memory polymers</article-title>
. <source>J. Mater. Chem.</source>
<volume>17</volume>
, <fpage>1543</fpage>
–<lpage>1558</lpage>
(<year>2007</year>
).</mixed-citation>
</ref>
<ref id="b12"><mixed-citation publication-type="journal"><name><surname>Buckley</surname>
<given-names>P. R.</given-names>
</name>
<italic>et al.</italic>
<article-title>Inductively heated shape memory polymer for the magnetic actuation of medical devices</article-title>
. <source>IEEE Trans. Biomed. Eng.</source>
<volume>53</volume>
, <fpage>2075</fpage>
–<lpage>2083</lpage>
(<year>2006</year>
).<pub-id pub-id-type="pmid">17019872</pub-id>
</mixed-citation>
</ref>
<ref id="b13"><mixed-citation publication-type="journal"><name><surname>Rousseau</surname>
<given-names>I. A.</given-names>
</name>
<article-title>Challenges of shape memory polymers: A review of the progress toward overcoming SMP’s limitations</article-title>
. <source>Polym. Eng. Sci.</source>
<volume>48</volume>
, <fpage>2075</fpage>
–<lpage>2089</lpage>
(<year>2008</year>
).</mixed-citation>
</ref>
<ref id="b14"><mixed-citation publication-type="other"><name><surname>Miles</surname>
<given-names>R. R.</given-names>
</name>
, <name><surname>Schumann</surname>
<given-names>D. L.</given-names>
</name>
, <name><surname>Pearson</surname>
<given-names>M. A.</given-names>
</name>
& <name><surname>Hilken</surname>
<given-names>D.</given-names>
</name>
<article-title>Steerable catheter with distending lumen-actuated curling catheter tip</article-title>
. (<year>2010</year>
). US patent US20100010437.</mixed-citation>
</ref>
<ref id="b15"><mixed-citation publication-type="other"><name><surname>Guo</surname>
<given-names>S.</given-names>
</name>
<italic>et al.</italic>
Micro catheter system with active guide wire-structure, experimental results and characteristic evaluation of active guide wire catheter using ICPF actuator. In, <italic>1994 5th International Symposium on Micro Machine and Human Science, 1994. Proceedings</italic>
191– (<year>1994</year>
). <pub-id pub-id-type="doi">10.1109/ISMMHS.1994.512923.</pub-id>
</mixed-citation>
</ref>
<ref id="b16"><mixed-citation publication-type="other"><name><surname>Guo</surname>
<given-names>S.</given-names>
</name>
, <name><surname>Nakamura</surname>
<given-names>T.</given-names>
</name>
, <name><surname>Fukuda</surname>
<given-names>T.</given-names>
</name>
, <name><surname>Oguro</surname>
<given-names>K.</given-names>
</name>
& <name><surname>Negoro</surname>
<given-names>M.</given-names>
</name>
Micro active catheter using ICPF actuator-characteristic evaluation, electrical model and operability evaluation. In, <italic>Proceedings of the 1996 IEEE IECON 22nd International Conference on Industrial Electronics, Control, and Instrumentation, 1996</italic>
<bold>2,</bold>
1312–1317 vol.2 (<year>1996</year>
).</mixed-citation>
</ref>
<ref id="b17"><mixed-citation publication-type="other"><name><surname>Sewa</surname>
<given-names>S.</given-names>
</name>
, <name><surname>Onishi</surname>
<given-names>K.</given-names>
</name>
, <name><surname>Asaka</surname>
<given-names>K.</given-names>
</name>
, <name><surname>Fujiwara</surname>
<given-names>N.</given-names>
</name>
& <name><surname>Oguro</surname>
<given-names>K.</given-names>
</name>
Polymer actuator driven by ion current at low voltage, applied to catheter system. In<italic>, The Eleventh Annual International Workshop on Micro Electro Mechanical Systems, 1998. MEMS 98. Proceedings</italic>
148–153 (<year>1998</year>
). <pub-id pub-id-type="doi">10.1109/MEMSYS.1998.659745.</pub-id>
</mixed-citation>
</ref>
<ref id="b18"><mixed-citation publication-type="journal"><name><surname>Daneshvar</surname>
<given-names>E. D.</given-names>
</name>
& <name><surname>Smela</surname>
<given-names>E.</given-names>
</name>
<article-title>Characterization of Conjugated Polymer Actuation under Cerebral Physiological Conditions</article-title>
. <source>Adv. Healthc. Mater.</source>
<volume>3</volume>
, <fpage>1026</fpage>
–<lpage>1035</lpage>
(<year>2014</year>
).<pub-id pub-id-type="pmid">24574101</pub-id>
</mixed-citation>
</ref>
<ref id="b19"><mixed-citation publication-type="journal"><name><surname>Bauer</surname>
<given-names>F.</given-names>
</name>
<article-title>Relaxor fluorinated polymers: novel applications and recent developments</article-title>
. <source>IEEE Trans. Dielectr. Electr. Insul.</source>
<volume>17</volume>
, <fpage>1106</fpage>
–<lpage>1112</lpage>
(<year>2010</year>
).</mixed-citation>
</ref>
<ref id="b20"><mixed-citation publication-type="journal"><name><surname>Choi</surname>
<given-names>S. T.</given-names>
</name>
, <name><surname>Kwon</surname>
<given-names>J. O.</given-names>
</name>
& <name><surname>Bauer</surname>
<given-names>F.</given-names>
</name>
<article-title>Multilayered relaxor ferroelectric polymer actuators for low-voltage operation fabricated with an adhesion-mediated film transfer technique</article-title>
. <source>Sens. Actuators Phys.</source>
<volume>203</volume>
, <fpage>282</fpage>
–<lpage>290</lpage>
(<year>2013</year>
).</mixed-citation>
</ref>
<ref id="b21"><mixed-citation publication-type="journal"><name><surname>Capsal</surname>
<given-names>J.-F.</given-names>
</name>
, <name><surname>Galineau</surname>
<given-names>J.</given-names>
</name>
, <name><surname>Le</surname>
<given-names>M.-Q.</given-names>
</name>
, <name><surname>Domingues Dos Santos</surname>
<given-names>F.</given-names>
</name>
& <name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
<article-title>Enhanced electrostriction based on plasticized relaxor ferroelectric P(VDF-TrFE-CFE/CTFE) blends</article-title>
. <source>J. Polym. Sci. Part B Polym. Phys.</source>
<volume>53</volume>
, <fpage>1368</fpage>
–<lpage>1379</lpage>
(<year>2015</year>
).</mixed-citation>
</ref>
<ref id="b22"><mixed-citation publication-type="journal"><name><surname>Capsal</surname>
<given-names>J.-F.</given-names>
</name>
, <name><surname>Galineau</surname>
<given-names>J.</given-names>
</name>
, <name><surname>Lallart</surname>
<given-names>M.</given-names>
</name>
, <name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
& <name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
<article-title>Plasticized relaxor ferroelectric terpolymer: Toward giant electrostriction, high mechanical energy and low electric field actuators</article-title>
. <source>Sens. Actuators Phys.</source>
<volume>207</volume>
, <fpage>25</fpage>
–<lpage>31</lpage>
(<year>2014</year>
).</mixed-citation>
</ref>
<ref id="b23"><mixed-citation publication-type="journal"><name><surname>Capsal</surname>
<given-names>J.-F.</given-names>
</name>
, <name><surname>Dantras</surname>
<given-names>E.</given-names>
</name>
& <name><surname>Lacabanne</surname>
<given-names>C.</given-names>
</name>
<article-title>Molecular mobility interpretation of the dielectric relaxor behavior in fluorinated copolymers and terpolymers</article-title>
. <source>J. Non-Cryst. Solids</source>
<volume>363</volume>
, <fpage>20</fpage>
–<lpage>25</lpage>
(<year>2013</year>
).</mixed-citation>
</ref>
<ref id="b24"><mixed-citation publication-type="journal"><name><surname>Le</surname>
<given-names>M. Q.</given-names>
</name>
<italic>et al.</italic>
<article-title>All-organic electrostrictive polymer composites with low driving electrical voltages for micro-fluidic pump applications</article-title>
. <source>Sci. Rep.</source>
<volume>5</volume>
, <fpage>11814</fpage>
(<year>2015</year>
).<pub-id pub-id-type="pmid">26139015</pub-id>
</mixed-citation>
</ref>
<ref id="b25"><mixed-citation publication-type="journal"><name><surname>Ganet</surname>
<given-names>F.</given-names>
</name>
<italic>et al.</italic>
<article-title>Haptic feedback using an all-organic electroactive polymer composite</article-title>
. <source>Sens. Actuators B Chem.</source>
<volume>220</volume>
, <fpage>1120</fpage>
–<lpage>1130</lpage>
(<year>2015</year>
).</mixed-citation>
</ref>
<ref id="b26"><mixed-citation publication-type="journal"><name><surname>Nordon</surname>
<given-names>I. M.</given-names>
</name>
, <name><surname>Hinchliffe</surname>
<given-names>R. J.</given-names>
</name>
, <name><surname>Holt</surname>
<given-names>P. J.</given-names>
</name>
, <name><surname>Loftus</surname>
<given-names>I. M.</given-names>
</name>
& <name><surname>Thompson</surname>
<given-names>M. M.</given-names>
</name>
<article-title>The requirement for smart catheters for advanced endovascular applications</article-title>
. <source>Proc. Inst. Mech. Eng. [H]</source>
<volume>224</volume>
, <fpage>743</fpage>
–<lpage>749</lpage>
(<year>2010</year>
).</mixed-citation>
</ref>
<ref id="b27"><mixed-citation publication-type="journal"><name><surname>Hutchins</surname>
<given-names>G. M.</given-names>
</name>
, <name><surname>Miner</surname>
<given-names>M. M.</given-names>
</name>
& <name><surname>Boitnott</surname>
<given-names>J. K.</given-names>
</name>
<article-title>Vessel caliber and branch-angle of human coronary artery branch-points</article-title>
. <source>Circ. Res.</source>
<volume>38</volume>
, <fpage>572</fpage>
–<lpage>576</lpage>
(<year>1976</year>
).<pub-id pub-id-type="pmid">1269108</pub-id>
</mixed-citation>
</ref>
<ref id="b28"><mixed-citation publication-type="journal"><name><surname>Breedveld</surname>
<given-names>P.</given-names>
</name>
, <name><surname>Sheltes</surname>
<given-names>J. S.</given-names>
</name>
, <name><surname>Blom</surname>
<given-names>E. M.</given-names>
</name>
& <name><surname>Verheij</surname>
<given-names>J. E. I.</given-names>
</name>
<article-title>A new, easily miniaturized steerable endoscope</article-title>
. <source>IEEE Eng. Med. Biol. Mag.</source>
<volume>24</volume>
, <fpage>40</fpage>
–<lpage>47</lpage>
(<year>2005</year>
).<pub-id pub-id-type="pmid">16382804</pub-id>
</mixed-citation>
</ref>
<ref id="b29"><mixed-citation publication-type="journal"><name><surname>Willey</surname>
<given-names>D. G.</given-names>
</name>
<article-title>Measuring reaction time</article-title>
. <source>Phys. Teach.</source>
<volume>23</volume>
, <fpage>314</fpage>
(<year>1985</year>
).</mixed-citation>
</ref>
<ref id="b30"><mixed-citation publication-type="journal"><name><surname>Petit</surname>
<given-names>L.</given-names>
</name>
, <name><surname>Guiffard</surname>
<given-names>B.</given-names>
</name>
, <name><surname>Seveyrat</surname>
<given-names>L.</given-names>
</name>
& <name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
<article-title>Actuating abilities of electroactive carbon nanopowder/polyurethane composite films</article-title>
. <source>Sens. Actuators Phys.</source>
<volume>148</volume>
, <fpage>105</fpage>
–<lpage>110</lpage>
(<year>2008</year>
).</mixed-citation>
</ref>
<ref id="b31"><mixed-citation publication-type="journal"><name><surname>Lallart</surname>
<given-names>M.</given-names>
</name>
, <name><surname>Capsal</surname>
<given-names>J.-F.</given-names>
</name>
, <name><surname>Sebald</surname>
<given-names>G.</given-names>
</name>
, <name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
& <name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
<article-title>Converse electrostrictive effect in dielectric polymers</article-title>
. <source>Sens. Actuators B Chem.</source>
<volume>190</volume>
, <fpage>259</fpage>
–<lpage>264</lpage>
(<year>2014</year>
).</mixed-citation>
</ref>
<ref id="b32"><mixed-citation publication-type="journal"><name><surname>Huang</surname>
<given-names>C.</given-names>
</name>
& <name><surname>Zhang</surname>
<given-names>Q.</given-names>
</name>
<article-title>Enhanced Dielectric and Electromechanical Responses in High Dielectric Constant All-Polymer Percolative Composites</article-title>
. <source>Adv. Funct. Mater.</source>
<volume>14</volume>
, <fpage>501</fpage>
–<lpage>506</lpage>
(<year>2004</year>
).</mixed-citation>
</ref>
<ref id="b33"><mixed-citation publication-type="journal"><name><surname>Song</surname>
<given-names>Y.</given-names>
</name>
, <name><surname>Guan</surname>
<given-names>Z.</given-names>
</name>
, <name><surname>Nie</surname>
<given-names>Y.</given-names>
</name>
& <name><surname>Guan</surname>
<given-names>X.</given-names>
</name>
<article-title>The analysis of the bending stiffness and intensity of cylindrical tubes</article-title>
. <source>Sci. China Ser. E Technol. Sci.</source>
<volume>50</volume>
, <fpage>268</fpage>
–<lpage>278</lpage>
(<year>2007</year>
).</mixed-citation>
</ref>
<ref id="b34"><mixed-citation publication-type="journal"><name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
, <name><surname>Yuse</surname>
<given-names>K.</given-names>
</name>
, <name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
, <name><surname>Kanda</surname>
<given-names>M.</given-names>
</name>
& <name><surname>Lebrun</surname>
<given-names>L.</given-names>
</name>
<article-title>Focus on the electrical field-induced strain of electroactive polymers and the observed saturation</article-title>
. <source>J. Appl. Phys.</source>
<volume>108</volume>
, <fpage>114910</fpage>
(<year>2010</year>
).</mixed-citation>
</ref>
<ref id="b35"><mixed-citation publication-type="journal"><name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
, <name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
, <name><surname>Guiffard</surname>
<given-names>B.</given-names>
</name>
, <name><surname>Lebrun</surname>
<given-names>L.</given-names>
</name>
& <name><surname>Putson</surname>
<given-names>C.</given-names>
</name>
<article-title>Electrostrictive polymer composite for energy harvesters and actuators</article-title>
. <source>J. Polym. Eng.</source>
<volume>31</volume>
(<year>2011</year>
).</mixed-citation>
</ref>
<ref id="b36"><mixed-citation publication-type="journal"><name><surname>Calvert</surname>
<given-names>P.</given-names>
</name>
<article-title>Inkjet Printing for Materials and Devices</article-title>
. - <source>Chem. Mater. ACS Publ.</source>
<volume>13</volume>
, <fpage>3299</fpage>
–<lpage>3305</lpage>
(<year>2001</year>
).</mixed-citation>
</ref>
<ref id="b37"><mixed-citation publication-type="journal"><name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
<italic>et al.</italic>
<article-title>Nonlinear strain–electric field relationship of carbon nanotube buckypaper/Nafion actuators</article-title>
. <source>Sens. Actuators Phys.</source>
<volume>170</volume>
, <fpage>164</fpage>
–<lpage>171</lpage>
(<year>2011</year>
).</mixed-citation>
</ref>
<ref id="b38"><mixed-citation publication-type="journal"><name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
<italic>et al.</italic>
<article-title>The compressive electrical field electrostrictive coefficient M33 of electroactive polymer composites and its saturation versus electrical field, polymer thickness, frequency, and fillers: THE ELECTROSTRICTIVE COEFFICIENT OF POLYMER COMPOSITES</article-title>
. <source>Polym. Adv. Technol.</source>
<volume>23</volume>
, <fpage>946</fpage>
–<lpage>950</lpage>
(<year>2012</year>
).</mixed-citation>
</ref>
<ref id="b39"><mixed-citation publication-type="journal"><name><surname>Liu</surname>
<given-names>Y.</given-names>
</name>
<italic>et al.</italic>
<article-title>Enhanced Electromechanical Response of Ionic Polymer Actuators by Improving Mechanical Coupling between Ions and Polymer Matrix</article-title>
. <source>Macromolecules</source>
<volume>45</volume>
, <fpage>5128</fpage>
–<lpage>5133</lpage>
(<year>2012</year>
).</mixed-citation>
</ref>
<ref id="b40"><mixed-citation publication-type="journal"><name><surname>Le</surname>
<given-names>Q. M.</given-names>
</name>
<italic>et al.</italic>
<article-title>Bilateral Control of Nonlinear Pneumatic Teleoperation System With Solenoid Valves. <italic>IEEE Trans</italic>
</article-title>
. <source>Control Syst. Technol.</source>
<volume>21</volume>
, <fpage>1463</fpage>
–<lpage>1470</lpage>
(<year>2013</year>
).</mixed-citation>
</ref>
<ref id="b41"><mixed-citation publication-type="journal"><name><surname>Shennib</surname>
<given-names>H.</given-names>
</name>
, <name><surname>Bastawisy</surname>
<given-names>A.</given-names>
</name>
, <name><surname>Mack</surname>
<given-names>M. J.</given-names>
</name>
& <name><surname>Moll</surname>
<given-names>F. H.</given-names>
</name>
<article-title>Computer-assisted telemanipulation: an enabling technology for endoscopic coronary artery bypass</article-title>
. <source>Ann. Thorac. Surg.</source>
<volume>66</volume>
, <fpage>1060</fpage>
–<lpage>1063</lpage>
(<year>1998</year>
).<pub-id pub-id-type="pmid">9769003</pub-id>
</mixed-citation>
</ref>
<ref id="b42"><mixed-citation publication-type="journal"><name><surname>Stephenson</surname>
<given-names>E. R.</given-names>
</name>
, <name><surname>Sankholkar</surname>
<given-names>S.</given-names>
</name>
, <name><surname>Ducko</surname>
<given-names>C. T.</given-names>
</name>
& <name><surname>Damiano</surname>
<given-names>R. J.</given-names>
</name>
<article-title>Robotically assisted microsurgery for endoscopic coronary artery bypass grafting</article-title>
. <source>Ann. Thorac. Surg.</source>
<volume>66</volume>
, <fpage>1064</fpage>
–<lpage>1067</lpage>
(<year>1998</year>
).<pub-id pub-id-type="pmid">9769004</pub-id>
</mixed-citation>
</ref>
<ref id="b43"><mixed-citation publication-type="other"><name><surname>Sanchez</surname>
<given-names>L. A.</given-names>
</name>
, <name><surname>Le</surname>
<given-names>M. Q.</given-names>
</name>
, <name><surname>Rabenorosoa</surname>
<given-names>K.</given-names>
</name>
, <name><surname>Liu</surname>
<given-names>C.</given-names>
</name>
, <name><surname>Zemiti</surname>
<given-names>N.</given-names>
</name>
, <name><surname>Poignet</surname>
<given-names>P.</given-names>
</name>
, <name><surname>Dombre</surname>
<given-names>E.</given-names>
</name>
, <name><surname>Menciassi</surname>
<given-names>A.</given-names>
</name>
& <name><surname>Dario</surname>
<given-names>P.</given-names>
</name>
“A Case Study of Safety in the Design of Surgical Robots: The ARAKNES platform”, International Conference on Intelligent Autonomous Systems, Korea, <year>2012</year>
.</mixed-citation>
</ref>
<ref id="b44"><mixed-citation publication-type="journal"><name><surname>Lallart</surname>
<given-names>M.</given-names>
</name>
, <name><surname>Cottinet</surname>
<given-names>P.-J.</given-names>
</name>
, <name><surname>Guyomar</surname>
<given-names>D.</given-names>
</name>
& <name><surname>Lebrun</surname>
<given-names>L.</given-names>
</name>
<article-title>Electrostrictive polymers for mechanical energy harvesting</article-title>
. <source>J. Polym. Sci. Part B Polym. Phys.</source>
<volume>50</volume>
, <fpage>523</fpage>
–<lpage>535</lpage>
(<year>2012</year>
).</mixed-citation>
</ref>
<ref id="b45"><mixed-citation publication-type="journal"><name><surname>Capsal</surname>
<given-names>J.-F.</given-names>
</name>
<italic>et al.</italic>
<article-title>Evaluation of macroscopic polarization and actuation abilities of electrostrictive dipolar polymers using the microscopic Debye/Langevin formalism</article-title>
. <source>J. Phys. Appl. Phys.</source>
<volume>45</volume>
, <fpage>205401</fpage>
(<year>2012</year>
).</mixed-citation>
</ref>
<ref id="b46"><mixed-citation publication-type="journal"><name><surname>Belhora</surname>
<given-names>F.</given-names>
</name>
<italic>et al.</italic>
<article-title>Optimization of energy harvesting conversion using the hybridization of electrostrictive polymers and electrets</article-title>
. <source>Sens. Actuators Phys.</source>
<volume>189</volume>
, <fpage>390</fpage>
–<lpage>398</lpage>
(<year>2013</year>
).</mixed-citation>
</ref>
<ref id="b47"><mixed-citation publication-type="journal"><name><surname>Faraz</surname>
<given-names>A.</given-names>
</name>
& <name><surname>Payandeh</surname>
<given-names>S.</given-names>
</name>
<source>Engineering Approaches to Mechanical and Robotic Design for Minimally Invasive Surgery (MIS).</source>
(Springer Science & Business Media, <year>2012</year>
).</mixed-citation>
</ref>
</ref-list>
<fn-group><fn><p><bold>Author Contributions</bold>
J.F.C., F.G. and M.Q.L. prepared the all-organic composite. J.F.C., F.G., M.Q.L. and P.J.C. fabricated the smart guide wire. P.J.C., L.P., J.F.C., P.L. and A.M. performed the data analysis. L.P. realized the finite element modelization. J.F.C., F.G. and M.Q.L. realized the smart guide wire characterization. M.Q.L., J.F.C. et P.J.C. planned the experiment and wrote the text. J.F.C. and P.J.C. supervised respectively the material and systems parts of the research. All authors reviewed the manuscript.</p>
</fn>
</fn-group>
</back>
<floats-group><fig id="f1"><label>Figure 1</label>
<caption><title>Schematic illustration of the “smart” guide wire application.</title>
</caption>
<graphic xlink:href="srep18593-f1"></graphic>
</fig>
<fig id="f2"><label>Figure 2</label>
<caption><title>Principle of a “smart” guide wire with 2 degrees of freedom.</title>
</caption>
<graphic xlink:href="srep18593-f2"></graphic>
</fig>
<fig id="f3"><label>Figure 3</label>
<caption><title>Electrostatic reparation in the in cross-section view.</title>
</caption>
<graphic xlink:href="srep18593-f3"></graphic>
</fig>
<fig id="f4"><label>Figure 4</label>
<caption><title>Bending displacement of two compositions of a terpolymer under a constant electrical field of 30 V/μm.</title>
</caption>
<graphic xlink:href="srep18593-f4"></graphic>
</fig>
<fig id="f5"><label>Figure 5</label>
<caption><title>Bending displacement along the guide wire length for a modified terpolymer.</title>
</caption>
<graphic xlink:href="srep18593-f5"></graphic>
</fig>
<fig id="f6"><label>Figure 6</label>
<caption><title>Extruded tube of P(VDF-TrFE-CTFE) with 15%wt DEHP.</title>
</caption>
<graphic xlink:href="srep18593-f6"></graphic>
</fig>
<fig id="f7"><label>Figure 7</label>
<caption><title>Schematic of the electromechanical characterization test setup of the “smart” guide wire.</title>
</caption>
<graphic xlink:href="srep18593-f7"></graphic>
</fig>
<fig id="f8"><label>Figure 8</label>
<caption><title>Experimental bending angles as a function of the electrical field.</title>
</caption>
<graphic xlink:href="srep18593-f8"></graphic>
</fig>
<fig id="f9"><label>Figure 9</label>
<caption><title>Smart guide wire for two electrical fields.</title>
</caption>
<graphic xlink:href="srep18593-f9"></graphic>
</fig>
<fig id="f10"><label>Figure 10</label>
<caption><title>Bending angle as a function of time under a step electrical field of 20 V/μm.</title>
</caption>
<graphic xlink:href="srep18593-f10"></graphic>
</fig>
<fig id="f11"><label>Figure 11</label>
<caption><title>Temporal evolution of the mechanical stress and generated charge.</title>
</caption>
<graphic xlink:href="srep18593-f11"></graphic>
</fig>
<fig id="f12"><label>Figure 12</label>
<caption><title>Electrical response in pseudo-piezoelectric mode as a function of the mechanical force.</title>
</caption>
<graphic xlink:href="srep18593-f12"></graphic>
</fig>
<fig id="f13"><label>Figure 13</label>
<caption><title>Electrical response in pseudo-piezoelectric mode as a function of the mechanical force.</title>
</caption>
<graphic xlink:href="srep18593-f13"></graphic>
</fig>
<fig id="f14"><label>Figure 14</label>
<caption><title>Pseudo-piezoelectric coefficient at 1Hz as a function of the static electrical field.</title>
</caption>
<graphic xlink:href="srep18593-f14"></graphic>
</fig>
<table-wrap position="float" id="t1"><label>Table 1</label>
<caption><title>Ansys parameters and variables.</title>
</caption>
<table frame="hsides" rules="groups" border="1"><colgroup><col align="left"></col>
<col align="center"></col>
<col align="center"></col>
</colgroup>
<thead valign="bottom"><tr><th align="left" valign="top" charoff="50">Name</th>
<th align="center" valign="top" charoff="50">Value</th>
<th align="center" valign="top" charoff="50">Description</th>
</tr>
</thead>
<tbody valign="top"><tr><td align="left" valign="top" charoff="50">D<sub>outer</sub>
</td>
<td align="center" valign="top" charoff="50">1.4 mm</td>
<td align="center" valign="top" charoff="50">Outer diameters</td>
</tr>
<tr><td align="left" valign="top" charoff="50">D<sub>inner</sub>
</td>
<td align="center" valign="top" charoff="50">1 mm</td>
<td align="center" valign="top" charoff="50">Inner diameters</td>
</tr>
<tr><td align="left" valign="top" charoff="50">L</td>
<td align="center" valign="top" charoff="50">60 mm</td>
<td align="center" valign="top" charoff="50">Extrusion Length</td>
</tr>
<tr><td align="left" valign="top" charoff="50">E</td>
<td align="center" valign="top" charoff="50">30 V/μm</td>
<td align="center" valign="top" charoff="50">Electric field</td>
</tr>
</tbody>
</table>
</table-wrap>
<table-wrap position="float" id="t2"><label>Table 2</label>
<caption><title>Electromechanical properties of electroactive polymers at room temperature.</title>
</caption>
<table frame="hsides" rules="groups" border="1"><colgroup><col align="left"></col>
<col align="center"></col>
<col align="center"></col>
<col align="center"></col>
</colgroup>
<thead valign="bottom"><tr><th align="left" valign="top" charoff="50">Type</th>
<th align="center" valign="top" charoff="50">Y (MPa)</th>
<th align="center" valign="top" charoff="50">ɛ<sub>r</sub>
at 0.1Hz and E = 20 V/μm</th>
<th align="center" valign="top" charoff="50">M<sub>31</sub>
(m<sup>2</sup>
/V<sup>2</sup>
)</th>
</tr>
</thead>
<tbody valign="top"><tr><td align="left" valign="top" charoff="50">P(VDF-TrFE-CTFE)</td>
<td align="center" valign="top" charoff="50">100</td>
<td align="center" valign="top" charoff="50">30</td>
<td align="center" valign="top" charoff="50">3.10<sup>−18</sup>
</td>
</tr>
<tr><td align="left" valign="top" charoff="50">P(VDF-TrFE-CTFE) + 15wt%DEHP</td>
<td align="center" valign="top" charoff="50">30</td>
<td align="center" valign="top" charoff="50">400</td>
<td align="center" valign="top" charoff="50">38.10<sup>−18</sup>
</td>
</tr>
</tbody>
</table>
</table-wrap>
</floats-group>
</pmc>
<affiliations><list><country><li>France</li>
</country>
</list>
<tree><country name="France"><noRegion><name sortKey="Ganet, F" sort="Ganet, F" uniqKey="Ganet F" first="F." last="Ganet">F. Ganet</name>
</noRegion>
<name sortKey="Capsal, J F" sort="Capsal, J F" uniqKey="Capsal J" first="J. F." last="Capsal">J. F. Capsal</name>
<name sortKey="Cottinet, P J" sort="Cottinet, P J" uniqKey="Cottinet P" first="P. J." last="Cottinet">P. J. Cottinet</name>
<name sortKey="Ganet, F" sort="Ganet, F" uniqKey="Ganet F" first="F." last="Ganet">F. Ganet</name>
<name sortKey="Le, M Q" sort="Le, M Q" uniqKey="Le M" first="M. Q." last="Le">M. Q. Le</name>
<name sortKey="Lermusiaux, P" sort="Lermusiaux, P" uniqKey="Lermusiaux P" first="P." last="Lermusiaux">P. Lermusiaux</name>
<name sortKey="Lermusiaux, P" sort="Lermusiaux, P" uniqKey="Lermusiaux P" first="P." last="Lermusiaux">P. Lermusiaux</name>
<name sortKey="Millon, A" sort="Millon, A" uniqKey="Millon A" first="A." last="Millon">A. Millon</name>
<name sortKey="Millon, A" sort="Millon, A" uniqKey="Millon A" first="A." last="Millon">A. Millon</name>
<name sortKey="Petit, L" sort="Petit, L" uniqKey="Petit L" first="L." last="Petit">L. Petit</name>
</country>
</tree>
</affiliations>
</record>
Pour manipuler ce document sous Unix (Dilib)
EXPLOR_STEP=$WICRI_ROOT/Ticri/CIDE/explor/HapticV1/Data/Pmc/Checkpoint
HfdSelect -h $EXPLOR_STEP/biblio.hfd -nk 000635 | SxmlIndent | more
Ou
HfdSelect -h $EXPLOR_AREA/Data/Pmc/Checkpoint/biblio.hfd -nk 000635 | SxmlIndent | more
Pour mettre un lien sur cette page dans le réseau Wicri
{{Explor lien |wiki= Ticri/CIDE |area= HapticV1 |flux= Pmc |étape= Checkpoint |type= RBID |clé= PMC:4682083 |texte= Development of a smart guide wire using an electrostrictive polymer: option for steerable orientation and force feedback }}
Pour générer des pages wiki
HfdIndexSelect -h $EXPLOR_AREA/Data/Pmc/Checkpoint/RBID.i -Sk "pubmed:26673883" \ | HfdSelect -Kh $EXPLOR_AREA/Data/Pmc/Checkpoint/biblio.hfd \ | NlmPubMed2Wicri -a HapticV1
![]() | This area was generated with Dilib version V0.6.23. | ![]() |