The effects of cutting conditions on mixed ceramic and cubic boron nitride tool wear and on surface roughness during machining of X200Cr12 steel (60 HRC)
Identifieur interne : 000220 ( France/Analysis ); précédent : 000219; suivant : 000221The effects of cutting conditions on mixed ceramic and cubic boron nitride tool wear and on surface roughness during machining of X200Cr12 steel (60 HRC)
Auteurs : M A Yallese [Algérie, France] ; J-F Rigal [Algérie, France] ; K. Chaoui [Algérie, France] ; L. Boulanouar [Algérie, France]Source :
- Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture [ 0954-4054 ] ; 2005.
Abstract
Alumina-based mixed ceramic (CC650) and cubic boron nitride-based (CBN) (CBN7020) tools are becoming mostly preferred for machining under severe conditions. The aim of this study is to investigate the effect of cutting parameters on ceramic and CBN tool wear in the hard turning of X200Cr12 steel. The results indicate that the comparison span for both tool materials is limited to a speed of 180 m/min at which catastrophic ceramic cutting edge collapse took place. The tool life ratio rose from 4.37 to 17.14 when the cutting speed evolved from 90 to 180 m/min in favour of CBN, which resisted up to a cutting speed of 350 m/min. The feed rate effect on roughness (μm) is satisfactorily predicted by a power model deduced from experimental data and is compared with a theoretical model. A correlation between surface roughness and tool wear is proposed for the usual cutting speed ranges and for the two tested inserts respectively. The analysis also revealed that, under the allowable wear limit, the ceramic tool gave quality surfaces with higher roughness than the CBN tool. In conclusion, this work highlights the fact that 120 m/min is the optimal cutting speed value for machining X200Cr12 steel using CBN7020 while 60 m/min is the optimal cutting speed value for CC650 steel.
Url:
DOI: 10.1243/095440505X8082
Affiliations:
Links toward previous steps (curation, corpus...)
- to stream Istex, to step Corpus: 000C81
- to stream Istex, to step Curation: 000887
- to stream Istex, to step Checkpoint: 000295
- to stream Main, to step Merge: 000756
- to stream Main, to step Curation: 000736
- to stream Main, to step Exploration: 000736
- to stream France, to step Extraction: 000220
Links to Exploration step
ISTEX:89704D1971247663110D5DC9444F193CA074CD8CLe document en format XML
<record><TEI wicri:istexFullTextTei="biblStruct"><teiHeader><fileDesc><titleStmt><title>The effects of cutting conditions on mixed ceramic and cubic boron nitride tool wear and on surface roughness during machining of X200Cr12 steel (60 HRC)</title><author><name sortKey="Yallese, M A" sort="Yallese, M A" uniqKey="Yallese M" first="M A" last="Yallese">M A Yallese</name></author><author><name sortKey="Rigal, J F" sort="Rigal, J F" uniqKey="Rigal J" first="J-F" last="Rigal">J-F Rigal</name></author><author><name sortKey="Chaoui, K" sort="Chaoui, K" uniqKey="Chaoui K" first="K" last="Chaoui">K. Chaoui</name></author><author><name sortKey="Boulanouar, L" sort="Boulanouar, L" uniqKey="Boulanouar L" first="L" last="Boulanouar">L. Boulanouar</name></author></titleStmt><publicationStmt><idno type="wicri:source">ISTEX</idno><idno type="RBID">ISTEX:89704D1971247663110D5DC9444F193CA074CD8C</idno><date when="2005" year="2005">2005</date><idno type="doi">10.1243/095440505X8082</idno><idno type="url">https://api.istex.fr/document/89704D1971247663110D5DC9444F193CA074CD8C/fulltext/pdf</idno><idno type="wicri:Area/Istex/Corpus">000C81</idno><idno type="wicri:explorRef" wicri:stream="Istex" wicri:step="Corpus" wicri:corpus="ISTEX">000C81</idno><idno type="wicri:Area/Istex/Curation">000887</idno><idno type="wicri:Area/Istex/Checkpoint">000295</idno><idno type="wicri:explorRef" wicri:stream="Istex" wicri:step="Checkpoint">000295</idno><idno type="wicri:doubleKey">0954-4054:2005:Yallese M:the:effects:of</idno><idno type="wicri:Area/Main/Merge">000756</idno><idno type="wicri:Area/Main/Curation">000736</idno><idno type="wicri:Area/Main/Exploration">000736</idno><idno type="wicri:Area/France/Extraction">000220</idno></publicationStmt><sourceDesc><biblStruct><analytic><title level="a">The effects of cutting conditions on mixed ceramic and cubic boron nitride tool wear and on surface roughness during machining of X200Cr12 steel (60 HRC)</title><author><name sortKey="Yallese, M A" sort="Yallese, M A" uniqKey="Yallese M" first="M A" last="Yallese">M A Yallese</name><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>1Laboratoire de Mécanique et de Structures (LMS), 8 Mai 1945 University, Guelma</wicri:regionArea><wicri:noRegion>Guelma</wicri:noRegion></affiliation><affiliation wicri:level="3"><country xml:lang="fr">France</country><wicri:regionArea>2Laboratoire de Mécanique des Contacts et des Solides (LaMCoS), INSA de Lyon, Villeurbanne</wicri:regionArea><placeName><region type="region" nuts="2">Auvergne-Rhône-Alpes</region><region type="old region" nuts="2">Rhône-Alpes</region><settlement type="city">Villeurbanne</settlement><settlement type="city" wicri:auto="agglo">Lyon</settlement></placeName></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>3Laboratoire de Recherche en Mécanique des Matériaux et Maintenance Industrielle (LR3MI), Badji Mokhtar University, Annaba</wicri:regionArea><wicri:noRegion>Annaba</wicri:noRegion></affiliation></author><author><name sortKey="Rigal, J F" sort="Rigal, J F" uniqKey="Rigal J" first="J-F" last="Rigal">J-F Rigal</name><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>1Laboratoire de Mécanique et de Structures (LMS), 8 Mai 1945 University, Guelma</wicri:regionArea><wicri:noRegion>Guelma</wicri:noRegion></affiliation><affiliation wicri:level="3"><country xml:lang="fr">France</country><wicri:regionArea>2Laboratoire de Mécanique des Contacts et des Solides (LaMCoS), INSA de Lyon, Villeurbanne</wicri:regionArea><placeName><region type="region" nuts="2">Auvergne-Rhône-Alpes</region><region type="old region" nuts="2">Rhône-Alpes</region><settlement type="city">Villeurbanne</settlement><settlement type="city" wicri:auto="agglo">Lyon</settlement></placeName></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>3Laboratoire de Recherche en Mécanique des Matériaux et Maintenance Industrielle (LR3MI), Badji Mokhtar University, Annaba</wicri:regionArea><wicri:noRegion>Annaba</wicri:noRegion></affiliation></author><author><name sortKey="Chaoui, K" sort="Chaoui, K" uniqKey="Chaoui K" first="K" last="Chaoui">K. Chaoui</name><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>1Laboratoire de Mécanique et de Structures (LMS), 8 Mai 1945 University, Guelma</wicri:regionArea><wicri:noRegion>Guelma</wicri:noRegion></affiliation><affiliation wicri:level="3"><country xml:lang="fr">France</country><wicri:regionArea>2Laboratoire de Mécanique des Contacts et des Solides (LaMCoS), INSA de Lyon, Villeurbanne</wicri:regionArea><placeName><region type="region" nuts="2">Auvergne-Rhône-Alpes</region><region type="old region" nuts="2">Rhône-Alpes</region><settlement type="city">Villeurbanne</settlement><settlement type="city" wicri:auto="agglo">Lyon</settlement></placeName></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>3Laboratoire de Recherche en Mécanique des Matériaux et Maintenance Industrielle (LR3MI), Badji Mokhtar University, Annaba</wicri:regionArea><wicri:noRegion>Annaba</wicri:noRegion></affiliation></author><author><name sortKey="Boulanouar, L" sort="Boulanouar, L" uniqKey="Boulanouar L" first="L" last="Boulanouar">L. Boulanouar</name><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation><wicri:noCountry code="syntax">???</wicri:noCountry></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>1Laboratoire de Mécanique et de Structures (LMS), 8 Mai 1945 University, Guelma</wicri:regionArea><wicri:noRegion>Guelma</wicri:noRegion></affiliation><affiliation wicri:level="3"><country xml:lang="fr">France</country><wicri:regionArea>2Laboratoire de Mécanique des Contacts et des Solides (LaMCoS), INSA de Lyon, Villeurbanne</wicri:regionArea><placeName><region type="region" nuts="2">Auvergne-Rhône-Alpes</region><region type="old region" nuts="2">Rhône-Alpes</region><settlement type="city">Villeurbanne</settlement><settlement type="city" wicri:auto="agglo">Lyon</settlement></placeName></affiliation><affiliation wicri:level="1"><country xml:lang="fr">Algérie</country><wicri:regionArea>3Laboratoire de Recherche en Mécanique des Matériaux et Maintenance Industrielle (LR3MI), Badji Mokhtar University, Annaba</wicri:regionArea><wicri:noRegion>Annaba</wicri:noRegion></affiliation></author></analytic><monogr></monogr><series><title level="j">Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture</title><idno type="ISSN">0954-4054</idno><idno type="eISSN">2041-1975</idno><imprint><publisher>SAGE Publications</publisher><pubPlace>Sage UK: London, England</pubPlace><date type="published" when="2005">2005</date><biblScope unit="volume">219</biblScope><biblScope unit="issue">1</biblScope><biblScope unit="page" from="35">35</biblScope><biblScope unit="page" to="55">55</biblScope></imprint><idno type="ISSN">0954-4054</idno></series><idno type="istex">89704D1971247663110D5DC9444F193CA074CD8C</idno><idno type="DOI">10.1243/095440505X8082</idno><idno type="ArticleID">10.1243_095440505X8082</idno></biblStruct></sourceDesc><seriesStmt><idno type="ISSN">0954-4054</idno></seriesStmt></fileDesc><profileDesc><textClass></textClass></profileDesc></teiHeader><front><div type="abstract">Alumina-based mixed ceramic (CC650) and cubic boron nitride-based (CBN) (CBN7020) tools are becoming mostly preferred for machining under severe conditions. The aim of this study is to investigate the effect of cutting parameters on ceramic and CBN tool wear in the hard turning of X200Cr12 steel. The results indicate that the comparison span for both tool materials is limited to a speed of 180 m/min at which catastrophic ceramic cutting edge collapse took place. The tool life ratio rose from 4.37 to 17.14 when the cutting speed evolved from 90 to 180 m/min in favour of CBN, which resisted up to a cutting speed of 350 m/min. The feed rate effect on roughness (μm) is satisfactorily predicted by a power model deduced from experimental data and is compared with a theoretical model. A correlation between surface roughness and tool wear is proposed for the usual cutting speed ranges and for the two tested inserts respectively. The analysis also revealed that, under the allowable wear limit, the ceramic tool gave quality surfaces with higher roughness than the CBN tool. In conclusion, this work highlights the fact that 120 m/min is the optimal cutting speed value for machining X200Cr12 steel using CBN7020 while 60 m/min is the optimal cutting speed value for CC650 steel.</div></front></TEI><affiliations><list><country><li>Algérie</li><li>France</li></country><region><li>Auvergne-Rhône-Alpes</li><li>Rhône-Alpes</li></region><settlement><li>Lyon</li><li>Villeurbanne</li></settlement></list><tree><country name="Algérie"><noRegion><name sortKey="Yallese, M A" sort="Yallese, M A" uniqKey="Yallese M" first="M A" last="Yallese">M A Yallese</name></noRegion><name sortKey="Boulanouar, L" sort="Boulanouar, L" uniqKey="Boulanouar L" first="L" last="Boulanouar">L. Boulanouar</name><name sortKey="Boulanouar, L" sort="Boulanouar, L" uniqKey="Boulanouar L" first="L" last="Boulanouar">L. Boulanouar</name><name sortKey="Chaoui, K" sort="Chaoui, K" uniqKey="Chaoui K" first="K" last="Chaoui">K. Chaoui</name><name sortKey="Chaoui, K" sort="Chaoui, K" uniqKey="Chaoui K" first="K" last="Chaoui">K. Chaoui</name><name sortKey="Rigal, J F" sort="Rigal, J F" uniqKey="Rigal J" first="J-F" last="Rigal">J-F Rigal</name><name sortKey="Rigal, J F" sort="Rigal, J F" uniqKey="Rigal J" first="J-F" last="Rigal">J-F Rigal</name><name sortKey="Yallese, M A" sort="Yallese, M A" uniqKey="Yallese M" first="M A" last="Yallese">M A Yallese</name></country><country name="France"><region name="Auvergne-Rhône-Alpes"><name sortKey="Yallese, M A" sort="Yallese, M A" uniqKey="Yallese M" first="M A" last="Yallese">M A Yallese</name></region><name sortKey="Boulanouar, L" sort="Boulanouar, L" uniqKey="Boulanouar L" first="L" last="Boulanouar">L. Boulanouar</name><name sortKey="Chaoui, K" sort="Chaoui, K" uniqKey="Chaoui K" first="K" last="Chaoui">K. Chaoui</name><name sortKey="Rigal, J F" sort="Rigal, J F" uniqKey="Rigal J" first="J-F" last="Rigal">J-F Rigal</name></country></tree></affiliations></record>Pour manipuler ce document sous Unix (Dilib)
EXPLOR_STEP=$WICRI_ROOT/Wicri/Terre/explor/NickelMaghrebV1/Data/France/Analysis
HfdSelect -h $EXPLOR_STEP/biblio.hfd -nk 000220 | SxmlIndent | more
Ou
HfdSelect -h $EXPLOR_AREA/Data/France/Analysis/biblio.hfd -nk 000220 | SxmlIndent | more
Pour mettre un lien sur cette page dans le réseau Wicri
{{Explor lien
|wiki= Wicri/Terre
|area= NickelMaghrebV1
|flux= France
|étape= Analysis
|type= RBID
|clé= ISTEX:89704D1971247663110D5DC9444F193CA074CD8C
|texte= The effects of cutting conditions on mixed ceramic and cubic boron nitride tool wear and on surface roughness during machining of X200Cr12 steel (60 HRC)
}}
| This area was generated with Dilib version V0.6.27. |  |