Serveur d'exploration sur le patient édenté

Attention, ce site est en cours de développement !
Attention, site généré par des moyens informatiques à partir de corpus bruts.
Les informations ne sont donc pas validées.

Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework

Identifieur interne : 001497 ( Pmc/Checkpoint ); précédent : 001496; suivant : 001498

Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework

Auteurs : Antônio Francisco Grando [Brésil] ; Carlos Eduardo Edwards Rezende [Brésil] ; Edson Antônio Capello Sousa [Brésil] ; José Henrique Rubo [Brésil]

Source :

RBID : PMC:4072272

Abstract

Knowing how stresses are dissipated on the fixed implant-supported complex allows adequate treatment planning and better choice of the materials used for prosthesis fabrication.

Objectives

The aim of this study was to evaluate the deformation suffered by cantilevered implant-supported fixed prostheses frameworks cast in silver-palladium alloy and coated with two occlusal veneering materials: acrylic resin or porcelain.

Material and Methods

Two strain gauges were bonded to the inferior surface of the silver-palladium framework and two other were bonded to the occlusal surface of the prosthesis framework covered with ceramic and acrylic resin on each of its two halves. The framework was fixed to a metallic master model and a 35.2 N compression force was applied to the cantilever at 10, 15 and 20 mm from the most distal implant. The measurements of deformation by compression and tension were obtained. The statistical 2-way ANOVA test was used for individual analysis of the experiment variables and the Tukey test was used for the interrelation between all the variables (material and distance of force application).

Results

The results showed that both variables had influence on the studied factors (deformation by compression and tension).

Conclusion

The ceramic coating provided greater rigidity to the assembly and therefore less distortion compared with the uncoated framework and with the resin-coated framework. The cantilever arm length also influenced the prosthesis rigidity, causing higher deformation the farther the load was applied from the last implant.


Url:
DOI: 10.1590/1678-775720130517
PubMed: 25025562
PubMed Central: 4072272


Affiliations:


Links toward previous steps (curation, corpus...)


Links to Exploration step

PMC:4072272

Le document en format XML

<record>
<TEI>
<teiHeader>
<fileDesc>
<titleStmt>
<title xml:lang="en">Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework</title>
<author>
<name sortKey="Grando, Antonio Francisco" sort="Grando, Antonio Francisco" uniqKey="Grando A" first="Antônio Francisco" last="Grando">Antônio Francisco Grando</name>
<affiliation wicri:level="2">
<nlm:aff id="aff01"> Department of Dentistry, University of Paraná, Cascavel, PR, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Dentistry, University of Paraná, Cascavel, PR</wicri:regionArea>
<placeName>
<region type="state">Paraná (État)</region>
</placeName>
</affiliation>
</author>
<author>
<name sortKey="Rezende, Carlos Eduardo Edwards" sort="Rezende, Carlos Eduardo Edwards" uniqKey="Rezende C" first="Carlos Eduardo Edwards" last="Rezende">Carlos Eduardo Edwards Rezende</name>
<affiliation wicri:level="4">
<nlm:aff id="aff02"> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
<settlement type="city">São Paulo</settlement>
</placeName>
<orgName type="university">Université de São Paulo</orgName>
</affiliation>
</author>
<author>
<name sortKey="Sousa, Edson Antonio Capello" sort="Sousa, Edson Antonio Capello" uniqKey="Sousa E" first="Edson Antônio Capello" last="Sousa">Edson Antônio Capello Sousa</name>
<affiliation wicri:level="2">
<nlm:aff id="aff03"> Department of Mechanical Engineering, Bauru School of Engineering, Univ. Estadual Paulista - UNESP, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Mechanical Engineering, Bauru School of Engineering, Univ. Estadual Paulista - UNESP, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
</placeName>
</affiliation>
</author>
<author>
<name sortKey="Rubo, Jose Henrique" sort="Rubo, Jose Henrique" uniqKey="Rubo J" first="José Henrique" last="Rubo">José Henrique Rubo</name>
<affiliation wicri:level="4">
<nlm:aff id="aff02"> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
<settlement type="city">São Paulo</settlement>
</placeName>
<orgName type="university">Université de São Paulo</orgName>
</affiliation>
</author>
</titleStmt>
<publicationStmt>
<idno type="wicri:source">PMC</idno>
<idno type="pmid">25025562</idno>
<idno type="pmc">4072272</idno>
<idno type="url">http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4072272</idno>
<idno type="RBID">PMC:4072272</idno>
<idno type="doi">10.1590/1678-775720130517</idno>
<date when="2014">2014</date>
<idno type="wicri:Area/Pmc/Corpus">002F62</idno>
<idno type="wicri:explorRef" wicri:stream="Pmc" wicri:step="Corpus" wicri:corpus="PMC">002F62</idno>
<idno type="wicri:Area/Pmc/Curation">002F62</idno>
<idno type="wicri:explorRef" wicri:stream="Pmc" wicri:step="Curation">002F62</idno>
<idno type="wicri:Area/Pmc/Checkpoint">001497</idno>
<idno type="wicri:explorRef" wicri:stream="Pmc" wicri:step="Checkpoint">001497</idno>
</publicationStmt>
<sourceDesc>
<biblStruct>
<analytic>
<title xml:lang="en" level="a" type="main">Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework</title>
<author>
<name sortKey="Grando, Antonio Francisco" sort="Grando, Antonio Francisco" uniqKey="Grando A" first="Antônio Francisco" last="Grando">Antônio Francisco Grando</name>
<affiliation wicri:level="2">
<nlm:aff id="aff01"> Department of Dentistry, University of Paraná, Cascavel, PR, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Dentistry, University of Paraná, Cascavel, PR</wicri:regionArea>
<placeName>
<region type="state">Paraná (État)</region>
</placeName>
</affiliation>
</author>
<author>
<name sortKey="Rezende, Carlos Eduardo Edwards" sort="Rezende, Carlos Eduardo Edwards" uniqKey="Rezende C" first="Carlos Eduardo Edwards" last="Rezende">Carlos Eduardo Edwards Rezende</name>
<affiliation wicri:level="4">
<nlm:aff id="aff02"> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
<settlement type="city">São Paulo</settlement>
</placeName>
<orgName type="university">Université de São Paulo</orgName>
</affiliation>
</author>
<author>
<name sortKey="Sousa, Edson Antonio Capello" sort="Sousa, Edson Antonio Capello" uniqKey="Sousa E" first="Edson Antônio Capello" last="Sousa">Edson Antônio Capello Sousa</name>
<affiliation wicri:level="2">
<nlm:aff id="aff03"> Department of Mechanical Engineering, Bauru School of Engineering, Univ. Estadual Paulista - UNESP, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Mechanical Engineering, Bauru School of Engineering, Univ. Estadual Paulista - UNESP, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
</placeName>
</affiliation>
</author>
<author>
<name sortKey="Rubo, Jose Henrique" sort="Rubo, Jose Henrique" uniqKey="Rubo J" first="José Henrique" last="Rubo">José Henrique Rubo</name>
<affiliation wicri:level="4">
<nlm:aff id="aff02"> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP, Brazil.</nlm:aff>
<country xml:lang="fr" wicri:curation="lc">Brésil</country>
<wicri:regionArea> Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP</wicri:regionArea>
<placeName>
<region type="state">État de São Paulo</region>
<settlement type="city">São Paulo</settlement>
</placeName>
<orgName type="university">Université de São Paulo</orgName>
</affiliation>
</author>
</analytic>
<series>
<title level="j">Journal of Applied Oral Science</title>
<idno type="ISSN">1678-7757</idno>
<idno type="eISSN">1678-7765</idno>
<imprint>
<date when="2014">2014</date>
</imprint>
</series>
</biblStruct>
</sourceDesc>
</fileDesc>
<profileDesc>
<textClass></textClass>
</profileDesc>
</teiHeader>
<front>
<div type="abstract" xml:lang="en">
<p>Knowing how stresses are dissipated on the fixed implant-supported complex allows adequate treatment planning and better choice of the materials used for prosthesis fabrication.</p>
<sec>
<title>Objectives</title>
<p>The aim of this study was to evaluate the deformation suffered by cantilevered implant-supported fixed prostheses frameworks cast in silver-palladium alloy and coated with two occlusal veneering materials: acrylic resin or porcelain.</p>
</sec>
<sec>
<title>Material and Methods</title>
<p>Two strain gauges were bonded to the inferior surface of the silver-palladium framework and two other were bonded to the occlusal surface of the prosthesis framework covered with ceramic and acrylic resin on each of its two halves. The framework was fixed to a metallic master model and a 35.2 N compression force was applied to the cantilever at 10, 15 and 20 mm from the most distal implant. The measurements of deformation by compression and tension were obtained. The statistical 2-way ANOVA test was used for individual analysis of the experiment variables and the Tukey test was used for the interrelation between all the variables (material and distance of force application).</p>
</sec>
<sec>
<title>Results</title>
<p>The results showed that both variables had influence on the studied factors (deformation by compression and tension).</p>
</sec>
<sec>
<title>Conclusion</title>
<p>The ceramic coating provided greater rigidity to the assembly and therefore less distortion compared with the uncoated framework and with the resin-coated framework. The cantilever arm length also influenced the prosthesis rigidity, causing higher deformation the farther the load was applied from the last implant.</p>
</sec>
</div>
</front>
<back>
<div1 type="bibliography">
<listBibl>
<biblStruct>
<analytic>
<author>
<name sortKey="Aglietta, M" uniqKey="Aglietta M">M Aglietta</name>
</author>
<author>
<name sortKey="Siciliano, Vi" uniqKey="Siciliano V">VI Siciliano</name>
</author>
<author>
<name sortKey="Zwahlen, M" uniqKey="Zwahlen M">M Zwahlen</name>
</author>
<author>
<name sortKey="Br Gger, U" uniqKey="Br Gger U">U Brägger</name>
</author>
<author>
<name sortKey="Pjetursson, Be" uniqKey="Pjetursson B">BE Pjetursson</name>
</author>
<author>
<name sortKey="Lang, Np" uniqKey="Lang N">NP Lang</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Akca, K" uniqKey="Akca K">K Akça</name>
</author>
<author>
<name sortKey="Cehreli, Mc" uniqKey="Cehreli M">MC Cehreli</name>
</author>
<author>
<name sortKey="Iplikcioglu, H" uniqKey="Iplikcioglu H">H Iplikçioglu</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Castro, Gc" uniqKey="Castro G">GC Castro</name>
</author>
<author>
<name sortKey="Araujo, Ca" uniqKey="Araujo C">CA Araújo</name>
</author>
<author>
<name sortKey="Mesquita, Mf" uniqKey="Mesquita M">MF Mesquita</name>
</author>
<author>
<name sortKey="Consani, Rl" uniqKey="Consani R">RL Consani</name>
</author>
<author>
<name sortKey="N Bilo, Ma" uniqKey="N Bilo M">MA Nóbilo</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Cibirka, Rm" uniqKey="Cibirka R">RM Cibirka</name>
</author>
<author>
<name sortKey="Razzoog, Me" uniqKey="Razzoog M">ME Razzoog</name>
</author>
<author>
<name sortKey="Lang, Br" uniqKey="Lang B">BR Lang</name>
</author>
<author>
<name sortKey="Stohler, Cs" uniqKey="Stohler C">CS Stohler</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Ciftci, Y" uniqKey="Ciftci Y">Y Çiftçi</name>
</author>
<author>
<name sortKey="Canay, S" uniqKey="Canay S">S Canay</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Ciftci, Y" uniqKey="Ciftci Y">Y Çiftçi</name>
</author>
<author>
<name sortKey="Canay, S" uniqKey="Canay S">S Canay</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Davis, Dm" uniqKey="Davis D">DM Davis</name>
</author>
<author>
<name sortKey="Rimrott, R" uniqKey="Rimrott R">R Rimrott</name>
</author>
<author>
<name sortKey="Zarb, Ga" uniqKey="Zarb G">GA Zarb</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Gracis, Se" uniqKey="Gracis S">SE Gracis</name>
</author>
<author>
<name sortKey="Nicholls, Ji" uniqKey="Nicholls J">JI Nicholls</name>
</author>
<author>
<name sortKey="Chalupnik, Jd" uniqKey="Chalupnik J">JD Chalupnik</name>
</author>
<author>
<name sortKey="Yuodelis, Ra" uniqKey="Yuodelis R">RA Yuodelis</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Hollweg, H" uniqKey="Hollweg H">H Hollweg</name>
</author>
<author>
<name sortKey="Jacques, Lb" uniqKey="Jacques L">LB Jacques</name>
</author>
<author>
<name sortKey="Moura, Ms" uniqKey="Moura M">MS Moura</name>
</author>
<author>
<name sortKey="Bianco, Vc" uniqKey="Bianco V">VC Bianco</name>
</author>
<author>
<name sortKey="Sousa, Ea" uniqKey="Sousa E">EA Sousa</name>
</author>
<author>
<name sortKey="Rubo, Jh" uniqKey="Rubo J">JH Rubo</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Jacobi, R" uniqKey="Jacobi R">R Jacobi</name>
</author>
<author>
<name sortKey="Shillingburg, Ht" uniqKey="Shillingburg H">HT Shillingburg</name>
</author>
<author>
<name sortKey="Duncanson, Mg" uniqKey="Duncanson M">MG Duncanson</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Jaques, Lb" uniqKey="Jaques L">LB Jaques</name>
</author>
<author>
<name sortKey="Moura, Ms" uniqKey="Moura M">MS Moura</name>
</author>
<author>
<name sortKey="Suedam, V" uniqKey="Suedam V">V Suedam</name>
</author>
<author>
<name sortKey="Souza, Ea" uniqKey="Souza E">EA Souza</name>
</author>
<author>
<name sortKey="Rubo, Jh" uniqKey="Rubo J">JH Rubo</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Korioth, Tw" uniqKey="Korioth T">TW Korioth</name>
</author>
<author>
<name sortKey="Johann, Ar" uniqKey="Johann A">AR Johann</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Naconecy, Mm" uniqKey="Naconecy M">MM Naconecy</name>
</author>
<author>
<name sortKey="Geremia, T" uniqKey="Geremia T">T Geremia</name>
</author>
<author>
<name sortKey="Cervieri, A" uniqKey="Cervieri A">A Cervieri</name>
</author>
<author>
<name sortKey="Teixeira, Er" uniqKey="Teixeira E">ER Teixeira</name>
</author>
<author>
<name sortKey="Shinkai, Rs" uniqKey="Shinkai R">RS Shinkai</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Purcell, Ba" uniqKey="Purcell B">BA Purcell</name>
</author>
<author>
<name sortKey="Mcglumphy, Ea" uniqKey="Mcglumphy E">EA McGlumphy</name>
</author>
<author>
<name sortKey="Holloway, Ja" uniqKey="Holloway J">JA Holloway</name>
</author>
<author>
<name sortKey="Beck, Fm" uniqKey="Beck F">FM Beck</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Rangert, B" uniqKey="Rangert B">B Rangert</name>
</author>
<author>
<name sortKey="Jemt, T" uniqKey="Jemt T">T Jemt</name>
</author>
<author>
<name sortKey="Jorneus, L" uniqKey="Jorneus L">L Jörneus</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Rubo, Jh" uniqKey="Rubo J">JH Rubo</name>
</author>
<author>
<name sortKey="Capello Souza, Ea" uniqKey="Capello Souza E">EA Capello Souza</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Salvi, Ge" uniqKey="Salvi G">GE Salvi</name>
</author>
<author>
<name sortKey="Br Gger, U" uniqKey="Br Gger U">U Brägger</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Santiago, Jf" uniqKey="Santiago J">JF Santiago</name>
</author>
<author>
<name sortKey="Pellizzer, Ep" uniqKey="Pellizzer E">EP Pellizzer</name>
</author>
<author>
<name sortKey="Verri, Fr" uniqKey="Verri F">FR Verri</name>
</author>
<author>
<name sortKey="Carvalho, Ps" uniqKey="Carvalho P">PS Carvalho</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Sertgoz, A" uniqKey="Sertgoz A">A Sertgöz</name>
</author>
<author>
<name sortKey="Guvener, S" uniqKey="Guvener S">S Güvener</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Sousa, Tc" uniqKey="Sousa T">TC Sousa</name>
</author>
<author>
<name sortKey="Lelis, V" uniqKey="Lelis V">V Lelis</name>
</author>
<author>
<name sortKey="Santos, Vm" uniqKey="Santos V">VM Santos</name>
</author>
<author>
<name sortKey="Nishioka, Gn" uniqKey="Nishioka G">GN Nishioka</name>
</author>
<author>
<name sortKey="Vasconcellos, Lg" uniqKey="Vasconcellos L">LG Vasconcellos</name>
</author>
<author>
<name sortKey="Nishioka, Rs" uniqKey="Nishioka R">RS Nishioka</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Stafford, Gl" uniqKey="Stafford G">GL Stafford</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Stegaroiu, R" uniqKey="Stegaroiu R">R Stegaroiu</name>
</author>
<author>
<name sortKey="Kusakari, H" uniqKey="Kusakari H">H Kusakari</name>
</author>
<author>
<name sortKey="Nishiyama, S" uniqKey="Nishiyama S">S Nishiyama</name>
</author>
<author>
<name sortKey="Miyakawa, O" uniqKey="Miyakawa O">O Miyakawa</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Tanaka, Y" uniqKey="Tanaka Y">Y Tanaka</name>
</author>
<author>
<name sortKey="Sugimoto, T" uniqKey="Sugimoto T">T Sugimoto</name>
</author>
<author>
<name sortKey="Tanaka, S" uniqKey="Tanaka S">S Tanaka</name>
</author>
<author>
<name sortKey="Hiranuma, K" uniqKey="Hiranuma K">K Hiranuma</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Teigen, K" uniqKey="Teigen K">K Teigen</name>
</author>
<author>
<name sortKey="Jokstad, A" uniqKey="Jokstad A">A Jokstad</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Van Zyl, Pp" uniqKey="Van Zyl P">PP Van Zyl</name>
</author>
<author>
<name sortKey="Grundling, Nl" uniqKey="Grundling N">NL Grundling</name>
</author>
<author>
<name sortKey="Jooste, Ch" uniqKey="Jooste C">CH Jooste</name>
</author>
<author>
<name sortKey="Terblanche, E" uniqKey="Terblanche E">E Terblanche</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="White, Sn" uniqKey="White S">SN White</name>
</author>
<author>
<name sortKey="Caputo, Aa" uniqKey="Caputo A">AA Caputo</name>
</author>
<author>
<name sortKey="Anderkvist, T" uniqKey="Anderkvist T">T Anderkvist</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Zarb, Ga" uniqKey="Zarb G">GA Zarb</name>
</author>
<author>
<name sortKey="Schmitt, A" uniqKey="Schmitt A">A Schmitt</name>
</author>
</analytic>
</biblStruct>
<biblStruct>
<analytic>
<author>
<name sortKey="Zarb, Ga" uniqKey="Zarb G">GA Zarb</name>
</author>
<author>
<name sortKey="Schmitt, A" uniqKey="Schmitt A">A Schmitt</name>
</author>
</analytic>
</biblStruct>
</listBibl>
</div1>
</back>
</TEI>
<pmc article-type="research-article">
<pmc-dir>properties open_access</pmc-dir>
<front>
<journal-meta>
<journal-id journal-id-type="nlm-ta">J Appl Oral Sci</journal-id>
<journal-id journal-id-type="iso-abbrev">J Appl Oral Sci</journal-id>
<journal-id journal-id-type="publisher-id">J Appl Oral Sci</journal-id>
<journal-title-group>
<journal-title>Journal of Applied Oral Science</journal-title>
</journal-title-group>
<issn pub-type="ppub">1678-7757</issn>
<issn pub-type="epub">1678-7765</issn>
<publisher>
<publisher-name>Faculdade de Odontologia de Bauru da Universidade de São Paulo</publisher-name>
</publisher>
</journal-meta>
<article-meta>
<article-id pub-id-type="pmid">25025562</article-id>
<article-id pub-id-type="pmc">4072272</article-id>
<article-id pub-id-type="doi">10.1590/1678-775720130517</article-id>
<article-categories>
<subj-group subj-group-type="heading">
<subject>Original Articles</subject>
</subj-group>
</article-categories>
<title-group>
<article-title>Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework</article-title>
</title-group>
<contrib-group>
<contrib contrib-type="author">
<name>
<surname>GRANDO</surname>
<given-names>Antônio Francisco</given-names>
</name>
<xref ref-type="aff" rid="aff01">1</xref>
</contrib>
<contrib contrib-type="author">
<name>
<surname>REZENDE</surname>
<given-names>Carlos Eduardo Edwards</given-names>
</name>
<xref ref-type="aff" rid="aff02">2</xref>
</contrib>
<contrib contrib-type="author">
<name>
<surname>SOUSA</surname>
<given-names>Edson Antônio Capello</given-names>
</name>
<xref ref-type="aff" rid="aff03">3</xref>
</contrib>
<contrib contrib-type="author">
<name>
<surname>RUBO</surname>
<given-names>José Henrique</given-names>
</name>
<xref ref-type="aff" rid="aff02">2</xref>
</contrib>
</contrib-group>
<aff id="aff01">
<label>1</label>
Department of Dentistry, University of Paraná, Cascavel, PR, Brazil.</aff>
<aff id="aff02">
<label>2</label>
Department of Prosthodontics, Bauru School of Dentistry, University of São Paulo, Bauru, SP, Brazil.</aff>
<aff id="aff03">
<label>3</label>
Department of Mechanical Engineering, Bauru School of Engineering, Univ. Estadual Paulista - UNESP, Bauru, SP, Brazil.</aff>
<author-notes>
<corresp id="c01">
<bold>Corresponding address:</bold>
José H. Rubo - Departamento de Prótese - Faculdade de Odontologia de Bauru - Universidade de São Paulo - Alameda Dr. Octávio Pinheiro Brisola, 9-75 - Vila Universitária - Bauru - SP - 7012-901 - Brazil - Phone: 55-14-3235-8231 - e-mail:
<email>jrubo@fob.usp.br</email>
</corresp>
</author-notes>
<pub-date pub-type="ppub">
<season>May-Jun</season>
<year>2014</year>
</pub-date>
<volume>22</volume>
<issue>3</issue>
<fpage>209</fpage>
<lpage>217</lpage>
<history>
<date date-type="received">
<day>08</day>
<month>9</month>
<year>2013</year>
</date>
<date date-type="rev-recd">
<day>08</day>
<month>1</month>
<year>2014</year>
</date>
<date date-type="accepted">
<day>26</day>
<month>1</month>
<year>2014</year>
</date>
</history>
<permissions>
<license license-type="open-access" xlink:href="http://creativecommons.org/licenses/by-nc/3.0/">
<license-p>This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited. </license-p>
</license>
</permissions>
<abstract>
<p>Knowing how stresses are dissipated on the fixed implant-supported complex allows adequate treatment planning and better choice of the materials used for prosthesis fabrication.</p>
<sec>
<title>Objectives</title>
<p>The aim of this study was to evaluate the deformation suffered by cantilevered implant-supported fixed prostheses frameworks cast in silver-palladium alloy and coated with two occlusal veneering materials: acrylic resin or porcelain.</p>
</sec>
<sec>
<title>Material and Methods</title>
<p>Two strain gauges were bonded to the inferior surface of the silver-palladium framework and two other were bonded to the occlusal surface of the prosthesis framework covered with ceramic and acrylic resin on each of its two halves. The framework was fixed to a metallic master model and a 35.2 N compression force was applied to the cantilever at 10, 15 and 20 mm from the most distal implant. The measurements of deformation by compression and tension were obtained. The statistical 2-way ANOVA test was used for individual analysis of the experiment variables and the Tukey test was used for the interrelation between all the variables (material and distance of force application).</p>
</sec>
<sec>
<title>Results</title>
<p>The results showed that both variables had influence on the studied factors (deformation by compression and tension).</p>
</sec>
<sec>
<title>Conclusion</title>
<p>The ceramic coating provided greater rigidity to the assembly and therefore less distortion compared with the uncoated framework and with the resin-coated framework. The cantilever arm length also influenced the prosthesis rigidity, causing higher deformation the farther the load was applied from the last implant.</p>
</sec>
</abstract>
<kwd-group>
<kwd>Dental implants</kwd>
<kwd>Dental prosthesis design</kwd>
<kwd>Dental veneers</kwd>
<kwd>Implant-supported dental prosthesis</kwd>
</kwd-group>
</article-meta>
</front>
</pmc>
<affiliations>
<list>
<country>
<li>Brésil</li>
</country>
<region>
<li>Paraná (État)</li>
<li>État de São Paulo</li>
</region>
<settlement>
<li>São Paulo</li>
</settlement>
<orgName>
<li>Université de São Paulo</li>
</orgName>
</list>
<tree>
<country name="Brésil">
<region name="Paraná (État)">
<name sortKey="Grando, Antonio Francisco" sort="Grando, Antonio Francisco" uniqKey="Grando A" first="Antônio Francisco" last="Grando">Antônio Francisco Grando</name>
</region>
<name sortKey="Rezende, Carlos Eduardo Edwards" sort="Rezende, Carlos Eduardo Edwards" uniqKey="Rezende C" first="Carlos Eduardo Edwards" last="Rezende">Carlos Eduardo Edwards Rezende</name>
<name sortKey="Rubo, Jose Henrique" sort="Rubo, Jose Henrique" uniqKey="Rubo J" first="José Henrique" last="Rubo">José Henrique Rubo</name>
<name sortKey="Sousa, Edson Antonio Capello" sort="Sousa, Edson Antonio Capello" uniqKey="Sousa E" first="Edson Antônio Capello" last="Sousa">Edson Antônio Capello Sousa</name>
</country>
</tree>
</affiliations>
</record>

Pour manipuler ce document sous Unix (Dilib)

EXPLOR_STEP=$WICRI_ROOT/Wicri/Santé/explor/EdenteV2/Data/Pmc/Checkpoint
HfdSelect -h $EXPLOR_STEP/biblio.hfd -nk 001497 | SxmlIndent | more

Ou

HfdSelect -h $EXPLOR_AREA/Data/Pmc/Checkpoint/biblio.hfd -nk 001497 | SxmlIndent | more

Pour mettre un lien sur cette page dans le réseau Wicri

{{Explor lien
   |wiki=    Wicri/Santé
   |area=    EdenteV2
   |flux=    Pmc
   |étape=   Checkpoint
   |type=    RBID
   |clé=     PMC:4072272
   |texte=   Effect of veneering material on the deformation suffered by
implant-supported fixed prosthesis framework
}}

Pour générer des pages wiki

HfdIndexSelect -h $EXPLOR_AREA/Data/Pmc/Checkpoint/RBID.i   -Sk "pubmed:25025562" \
       | HfdSelect -Kh $EXPLOR_AREA/Data/Pmc/Checkpoint/biblio.hfd   \
       | NlmPubMed2Wicri -a EdenteV2 

Wicri

This area was generated with Dilib version V0.6.32.
Data generation: Thu Nov 30 15:26:48 2017. Site generation: Tue Mar 8 16:36:20 2022