Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric
Identifieur interne : 002475 ( Pmc/Curation ); précédent : 002474; suivant : 002476Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric
Auteurs : Tetsuyou Watanabe ; Takanobu Iwai ; Yoshinori Fujihira ; Lina Wakako ; Hiroyuki Kagawa ; Takeshi YoneyamaSource :
- Sensors (Basel, Switzerland) [ 1424-8220 ] ; 2014.
Abstract
An endoscope/fiberscope is a minimally invasive tool used for directly observing tissues in areas deep inside the human body where access is limited. However, this tool only yields visual information. If force feedback information were also available, endoscope/fiberscope operators would be able to detect indurated areas that are visually hard to recognize. Furthermore, obtaining such feedback information from tissues in areas where collecting visual information is a challenge would be highly useful. The major obstacle is that such force information is difficult to acquire. This paper presents a novel force sensing system that can be attached to a very thin fiberscope/endoscope. To ensure a small size, high resolution, easy sterilization, and low cost, the proposed force visualization–based system uses a highly elastic material—panty stocking fabric. The paper also presents the methodology for deriving the force value from the captured image. The system has a resolution of less than 0.01 N and sensitivity of greater than 600 pixels/N within the force range of 0–0.2 N.
Url:
DOI: 10.3390/s140305207
PubMed: 24625744
PubMed Central: 4003989
Links toward previous steps (curation, corpus...)
- to stream Pmc, to step Corpus: Pour aller vers cette notice dans l'étape Curation :002475
Links to Exploration step
PMC:4003989Le document en format XML
<record><TEI><teiHeader><fileDesc><titleStmt><title xml:lang="en">Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric</title>
<author><name sortKey="Watanabe, Tetsuyou" sort="Watanabe, Tetsuyou" uniqKey="Watanabe T" first="Tetsuyou" last="Watanabe">Tetsuyou Watanabe</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Iwai, Takanobu" sort="Iwai, Takanobu" uniqKey="Iwai T" first="Takanobu" last="Iwai">Takanobu Iwai</name>
<affiliation><nlm:aff id="af2-sensors-14-05207"> Department of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(T.I.);<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(Y.F.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Fujihira, Yoshinori" sort="Fujihira, Yoshinori" uniqKey="Fujihira Y" first="Yoshinori" last="Fujihira">Yoshinori Fujihira</name>
<affiliation><nlm:aff id="af2-sensors-14-05207"> Department of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(T.I.);<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(Y.F.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Wakako, Lina" sort="Wakako, Lina" uniqKey="Wakako L" first="Lina" last="Wakako">Lina Wakako</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Kagawa, Hiroyuki" sort="Kagawa, Hiroyuki" uniqKey="Kagawa H" first="Hiroyuki" last="Kagawa">Hiroyuki Kagawa</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Yoneyama, Takeshi" sort="Yoneyama, Takeshi" uniqKey="Yoneyama T" first="Takeshi" last="Yoneyama">Takeshi Yoneyama</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
</titleStmt>
<publicationStmt><idno type="wicri:source">PMC</idno>
<idno type="pmid">24625744</idno>
<idno type="pmc">4003989</idno>
<idno type="url">http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4003989</idno>
<idno type="RBID">PMC:4003989</idno>
<idno type="doi">10.3390/s140305207</idno>
<date when="2014">2014</date>
<idno type="wicri:Area/Pmc/Corpus">002475</idno>
<idno type="wicri:Area/Pmc/Curation">002475</idno>
</publicationStmt>
<sourceDesc><biblStruct><analytic><title xml:lang="en" level="a" type="main">Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric</title>
<author><name sortKey="Watanabe, Tetsuyou" sort="Watanabe, Tetsuyou" uniqKey="Watanabe T" first="Tetsuyou" last="Watanabe">Tetsuyou Watanabe</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Iwai, Takanobu" sort="Iwai, Takanobu" uniqKey="Iwai T" first="Takanobu" last="Iwai">Takanobu Iwai</name>
<affiliation><nlm:aff id="af2-sensors-14-05207"> Department of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(T.I.);<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(Y.F.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Fujihira, Yoshinori" sort="Fujihira, Yoshinori" uniqKey="Fujihira Y" first="Yoshinori" last="Fujihira">Yoshinori Fujihira</name>
<affiliation><nlm:aff id="af2-sensors-14-05207"> Department of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(T.I.);<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(Y.F.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Wakako, Lina" sort="Wakako, Lina" uniqKey="Wakako L" first="Lina" last="Wakako">Lina Wakako</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Kagawa, Hiroyuki" sort="Kagawa, Hiroyuki" uniqKey="Kagawa H" first="Hiroyuki" last="Kagawa">Hiroyuki Kagawa</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
<author><name sortKey="Yoneyama, Takeshi" sort="Yoneyama, Takeshi" uniqKey="Yoneyama T" first="Takeshi" last="Yoneyama">Takeshi Yoneyama</name>
<affiliation><nlm:aff id="af1-sensors-14-05207"> School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</nlm:aff>
</affiliation>
</author>
</analytic>
<series><title level="j">Sensors (Basel, Switzerland)</title>
<idno type="eISSN">1424-8220</idno>
<imprint><date when="2014">2014</date>
</imprint>
</series>
</biblStruct>
</sourceDesc>
</fileDesc>
<profileDesc><textClass></textClass>
</profileDesc>
</teiHeader>
<front><div type="abstract" xml:lang="en"><p>An endoscope/fiberscope is a minimally invasive tool used for directly observing tissues in areas deep inside the human body where access is limited. However, this tool only yields visual information. If force feedback information were also available, endoscope/fiberscope operators would be able to detect indurated areas that are visually hard to recognize. Furthermore, obtaining such feedback information from tissues in areas where collecting visual information is a challenge would be highly useful. The major obstacle is that such force information is difficult to acquire. This paper presents a novel force sensing system that can be attached to a very thin fiberscope/endoscope. To ensure a small size, high resolution, easy sterilization, and low cost, the proposed force visualization–based system uses a highly elastic material—panty stocking fabric. The paper also presents the methodology for deriving the force value from the captured image. The system has a resolution of less than 0.01 N and sensitivity of greater than 600 pixels/N within the force range of 0–0.2 N.</p>
</div>
</front>
<back><div1 type="bibliography"><listBibl><biblStruct><analytic><author><name sortKey="Puangmali, P" uniqKey="Puangmali P">P. Puangmali</name>
</author>
<author><name sortKey="Althoefer, K" uniqKey="Althoefer K">K. Althoefer</name>
</author>
<author><name sortKey="Seneviratne, D" uniqKey="Seneviratne D">D. Seneviratne</name>
</author>
<author><name sortKey="Murphy, D" uniqKey="Murphy D">D. Murphy</name>
</author>
<author><name sortKey="Dasgupta, P" uniqKey="Dasgupta P">P. Dasgupta</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Westebring Van Der Putten, E" uniqKey="Westebring Van Der Putten E">E. Westebring-van der Putten</name>
</author>
<author><name sortKey="Goossens, R" uniqKey="Goossens R">R. Goossens</name>
</author>
<author><name sortKey="Jakimowicz, J" uniqKey="Jakimowicz J">J. Jakimowicz</name>
</author>
<author><name sortKey="Dankelman, J" uniqKey="Dankelman J">J. Dankelman</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Okamura, A" uniqKey="Okamura A">A. Okamura</name>
</author>
<author><name sortKey="Verner, C" uniqKey="Verner C">C. Verner</name>
</author>
<author><name sortKey="Mahvash, M" uniqKey="Mahvash M">M. Mahvash</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Poorten, V E" uniqKey="Poorten V">V.E. Poorten</name>
</author>
<author><name sortKey="Demeester, E" uniqKey="Demeester E">E. Demeester</name>
</author>
<author><name sortKey="Lammertse, P" uniqKey="Lammertse P">P. Lammertse</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Tiwana, M I" uniqKey="Tiwana M">M.I. Tiwana</name>
</author>
<author><name sortKey="Redmond, S J" uniqKey="Redmond S">S.J. Redmond</name>
</author>
<author><name sortKey="Lovell, N H" uniqKey="Lovell N">N.H. Lovell</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Takaki, T" uniqKey="Takaki T">T. Takaki</name>
</author>
<author><name sortKey="Omasa, Y" uniqKey="Omasa Y">Y. Omasa</name>
</author>
<author><name sortKey="Ishii, I" uniqKey="Ishii I">I. Ishii</name>
</author>
<author><name sortKey="Kawahara, T" uniqKey="Kawahara T">T. Kawahara</name>
</author>
<author><name sortKey="Okajima, M" uniqKey="Okajima M">M. Okajima</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Tadano, K" uniqKey="Tadano K">K. Tadano</name>
</author>
<author><name sortKey="Kawashima, K" uniqKey="Kawashima K">K. Kawashima</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Kawahara, T" uniqKey="Kawahara T">T. Kawahara</name>
</author>
<author><name sortKey="Tanaka, S" uniqKey="Tanaka S">S. Tanaka</name>
</author>
<author><name sortKey="Kaneko, M" uniqKey="Kaneko M">M. Kaneko</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Peirs, J" uniqKey="Peirs J">J. Peirs</name>
</author>
<author><name sortKey="Clijnen, J" uniqKey="Clijnen J">J. Clijnen</name>
</author>
<author><name sortKey="Reynaerts, D" uniqKey="Reynaerts D">D. Reynaerts</name>
</author>
<author><name sortKey="Brussel, H V" uniqKey="Brussel H">H.V. Brussel</name>
</author>
<author><name sortKey="Herijgers, P" uniqKey="Herijgers P">P. Herijgers</name>
</author>
<author><name sortKey="Corteville, B" uniqKey="Corteville B">B. Corteville</name>
</author>
<author><name sortKey="Boone, S" uniqKey="Boone S">S. Boone</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Tada, M" uniqKey="Tada M">M. Tada</name>
</author>
<author><name sortKey="Sasaki, S" uniqKey="Sasaki S">S. Sasaki</name>
</author>
<author><name sortKey="Ogasawara, T" uniqKey="Ogasawara T">T. Ogasawara</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Ohka, M" uniqKey="Ohka M">M. Ohka</name>
</author>
<author><name sortKey="Mitsuya, Y" uniqKey="Mitsuya Y">Y. Mitsuya</name>
</author>
<author><name sortKey="Matsunaga, Y" uniqKey="Matsunaga Y">Y. Matsunaga</name>
</author>
<author><name sortKey="Takeuchi, S" uniqKey="Takeuchi S">S. Takeuchi</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Kamiyama, K" uniqKey="Kamiyama K">K. Kamiyama</name>
</author>
<author><name sortKey="Vlack, K" uniqKey="Vlack K">K. Vlack</name>
</author>
<author><name sortKey="Mizota, T" uniqKey="Mizota T">T. Mizota</name>
</author>
<author><name sortKey="Kajimoto, H" uniqKey="Kajimoto H">H. Kajimoto</name>
</author>
<author><name sortKey="Kawakami, N" uniqKey="Kawakami N">N. Kawakami</name>
</author>
<author><name sortKey="Tachi, S" uniqKey="Tachi S">S. Tachi</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Dahiya, R S" uniqKey="Dahiya R">R.S. Dahiya</name>
</author>
<author><name sortKey="Metta, G" uniqKey="Metta G">G. Metta</name>
</author>
<author><name sortKey="Valle, M" uniqKey="Valle M">M. Valle</name>
</author>
<author><name sortKey="Sandini, G" uniqKey="Sandini G">G. Sandini</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Yoneyama, T" uniqKey="Yoneyama T">T. Yoneyama</name>
</author>
<author><name sortKey="Watanabe, T" uniqKey="Watanabe T">T. Watanabe</name>
</author>
<author><name sortKey="Kagawa, H" uniqKey="Kagawa H">H. Kagawa</name>
</author>
<author><name sortKey="Hamada, J" uniqKey="Hamada J">J. Hamada</name>
</author>
<author><name sortKey="Hayashi, Y" uniqKey="Hayashi Y">Y. Hayashi</name>
</author>
<author><name sortKey="Nakada, M" uniqKey="Nakada M">M. Nakada</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Kanada, Y" uniqKey="Kanada Y">Y. Kanada</name>
</author>
<author><name sortKey="Yoneyama, T" uniqKey="Yoneyama T">T. Yoneyama</name>
</author>
<author><name sortKey="Watanabe, T" uniqKey="Watanabe T">T. Watanabe</name>
</author>
<author><name sortKey="Kagawa, H" uniqKey="Kagawa H">H. Kagawa</name>
</author>
<author><name sortKey="Sugiyama, N" uniqKey="Sugiyama N">N. Sugiyama</name>
</author>
<author><name sortKey="Tanaka, K" uniqKey="Tanaka K">K. Tanaka</name>
</author>
<author><name sortKey="Hanyu, T" uniqKey="Hanyu T">T. Hanyu</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Fujihira, Y" uniqKey="Fujihira Y">Y. Fujihira</name>
</author>
<author><name sortKey="Hanyu, T" uniqKey="Hanyu T">T. Hanyu</name>
</author>
<author><name sortKey="Kanada, Y" uniqKey="Kanada Y">Y. Kanada</name>
</author>
<author><name sortKey="Yoneyama, T" uniqKey="Yoneyama T">T. Yoneyama</name>
</author>
<author><name sortKey="Watanabe, T" uniqKey="Watanabe T">T. Watanabe</name>
</author>
<author><name sortKey="Kagawa, H" uniqKey="Kagawa H">H. Kagawa</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Kawabata, S" uniqKey="Kawabata S">S. Kawabata</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Kawabata, S A" uniqKey="Kawabata S">S. A Kawabata</name>
</author>
</analytic>
</biblStruct>
<biblStruct><analytic><author><name sortKey="Sanchez Duran, J A" uniqKey="Sanchez Duran J">J.A. Sánchez-Durán</name>
</author>
<author><name sortKey="Oballe Peinado, " uniqKey="Oballe Peinado ">Ó. Oballe-Peinado</name>
</author>
<author><name sortKey="Castellanos Ramos, J" uniqKey="Castellanos Ramos J">J. Castellanos-Ramos</name>
</author>
<author><name sortKey="Vidal Verdu, F" uniqKey="Vidal Verdu F">F. Vidal-Verdú</name>
</author>
</analytic>
</biblStruct>
</listBibl>
</div1>
</back>
</TEI>
<pmc article-type="research-article"><pmc-dir>properties open_access</pmc-dir>
<front><journal-meta><journal-id journal-id-type="nlm-ta">Sensors (Basel)</journal-id>
<journal-id journal-id-type="iso-abbrev">Sensors (Basel)</journal-id>
<journal-title-group><journal-title>Sensors (Basel, Switzerland)</journal-title>
</journal-title-group>
<issn pub-type="epub">1424-8220</issn>
<publisher><publisher-name>MDPI</publisher-name>
</publisher>
</journal-meta>
<article-meta><article-id pub-id-type="pmid">24625744</article-id>
<article-id pub-id-type="pmc">4003989</article-id>
<article-id pub-id-type="doi">10.3390/s140305207</article-id>
<article-id pub-id-type="publisher-id">sensors-14-05207</article-id>
<article-categories><subj-group subj-group-type="heading"><subject>Article</subject>
</subj-group>
</article-categories>
<title-group><article-title>Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric</article-title>
</title-group>
<contrib-group><contrib contrib-type="author"><name><surname>Watanabe</surname>
<given-names>Tetsuyou</given-names>
</name>
<xref ref-type="aff" rid="af1-sensors-14-05207"><sup>1</sup>
</xref>
<xref rid="c1-sensors-14-05207" ref-type="corresp"><sup>*</sup>
</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Iwai</surname>
<given-names>Takanobu</given-names>
</name>
<xref ref-type="aff" rid="af2-sensors-14-05207"><sup>2</sup>
</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Fujihira</surname>
<given-names>Yoshinori</given-names>
</name>
<xref ref-type="aff" rid="af2-sensors-14-05207"><sup>2</sup>
</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Wakako</surname>
<given-names>Lina</given-names>
</name>
<xref ref-type="aff" rid="af1-sensors-14-05207"><sup>1</sup>
</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Kagawa</surname>
<given-names>Hiroyuki</given-names>
</name>
<xref ref-type="aff" rid="af1-sensors-14-05207"><sup>1</sup>
</xref>
</contrib>
<contrib contrib-type="author"><name><surname>Yoneyama</surname>
<given-names>Takeshi</given-names>
</name>
<xref ref-type="aff" rid="af1-sensors-14-05207"><sup>1</sup>
</xref>
</contrib>
</contrib-group>
<aff id="af1-sensors-14-05207"><label>1</label>
School of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>linawakako@se.kanazawa-u.ac.jp</email>
(L.W.);<email>kagawa@se.kanazawa-u.ac.jp</email>
(H.K.);<email>yoneyama@se.kanazawa-u.ac.jp</email>
(T.Y.)</aff>
<aff id="af2-sensors-14-05207"><label>2</label>
Department of Mechanical Engineering, College of Science and Engineering, Kanazawa University, Ishikawa, Japan; E-Mails:<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(T.I.);<email>fuji3134@stu.kanazawa-u.ac.jp</email>
(Y.F.)</aff>
<author-notes><corresp id="c1-sensors-14-05207"><label>*</label>
Author to whom correspondence should be addressed; E-Mail: <email>te-watanabe@ieee.org</email>
; Tel./Fax: +81-234-4684.</corresp>
</author-notes>
<pub-date pub-type="collection"><month>3</month>
<year>2014</year>
</pub-date>
<pub-date pub-type="epub"><day>12</day>
<month>3</month>
<year>2014</year>
</pub-date>
<volume>14</volume>
<issue>3</issue>
<fpage>5207</fpage>
<lpage>5220</lpage>
<history><date date-type="received"><day>06</day>
<month>12</month>
<year>2013</year>
</date>
<date date-type="rev-recd"><day>07</day>
<month>3</month>
<year>2014</year>
</date>
<date date-type="accepted"><day>10</day>
<month>3</month>
<year>2014</year>
</date>
</history>
<permissions><copyright-statement>© 2014 by the authors; licensee MDPI, Basel, Switzerland.</copyright-statement>
<copyright-year>2014</copyright-year>
<license><license-p>This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution license (<ext-link ext-link-type="uri" xlink:href="http://creativecommons.org/licenses/by/3.0/">http://creativecommons.org/licenses/by/3.0/</ext-link>
).</license-p>
</license>
</permissions>
<abstract><p>An endoscope/fiberscope is a minimally invasive tool used for directly observing tissues in areas deep inside the human body where access is limited. However, this tool only yields visual information. If force feedback information were also available, endoscope/fiberscope operators would be able to detect indurated areas that are visually hard to recognize. Furthermore, obtaining such feedback information from tissues in areas where collecting visual information is a challenge would be highly useful. The major obstacle is that such force information is difficult to acquire. This paper presents a novel force sensing system that can be attached to a very thin fiberscope/endoscope. To ensure a small size, high resolution, easy sterilization, and low cost, the proposed force visualization–based system uses a highly elastic material—panty stocking fabric. The paper also presents the methodology for deriving the force value from the captured image. The system has a resolution of less than 0.01 N and sensitivity of greater than 600 pixels/N within the force range of 0–0.2 N.</p>
</abstract>
<kwd-group><kwd>force sensing</kwd>
<kwd>force visualization</kwd>
<kwd>panty stocking</kwd>
<kwd>endoscope</kwd>
</kwd-group>
</article-meta>
</front>
<body><sec sec-type="intro"><label>1.</label>
<title>Introduction</title>
<p>The endoscope is becoming an increasingly important tool in the field of medicine. In physical examinations, endoscopes are a powerful tool for detecting diseases such as cancer. In medical operations, endoscopes allow practitioners to perform surgeries through small incisions, which can provide minimally invasive surgery and hence facilitate quick healing in patients. However, endoscopes do not give tactile/force information. Such information might be helpful for increasing the precision of examinations and improving the quality of treatments. In particular, tactile/force information is important when the visible area is limited. A typical example occurs in neurosurgery where the doctor is required to treat tumors that are seated deeply within the brain and surrounded by healthy tissues. Hence, the goal of this paper is to develop force sensors that can be attached to the tip of an endoscope so that the operator can investigate tissues seated deeply within organs.</p>
<p>Many force sensors have been developed for forceps and medical manipulators. Puangmali <italic>et al.</italic>
[<xref rid="b1-sensors-14-05207" ref-type="bibr">1</xref>
] reviewed previously conducted researches of force and tactile sensors for minimally invasive surgery. The purpose of force sensing is to give feedback to the operator on the sensation of touching an organ, namely, force/haptic feedback (see [<xref rid="b2-sensors-14-05207" ref-type="bibr">2</xref>
–<xref rid="b5-sensors-14-05207" ref-type="bibr">5</xref>
] for reviews). Most force sensors that have been developed include electric devices such as strain gauges. However, electrical devices are not always suitable for medical devices. Electrical force sensors need amplifiers and wiring for signal transfer. This causes the size and cost of the overall system to become large. In addition, sterilizing or disinfecting such electrical devices is difficult. In special environments such as those of magnetic resonance imaging (MRI), the use of electricity should be avoided. One solution to these issues is to not use electrical parts such as wiring and circuits. Takaki <italic>et al.</italic>
[<xref rid="b6-sensors-14-05207" ref-type="bibr">6</xref>
] developed a force sensor based on force visualization by using moiré fringe patterns. Tadano and Kawashima [<xref rid="b7-sensors-14-05207" ref-type="bibr">7</xref>
] developed a system to generate feedback on force sensation without a force sensor by utilizing a pneumatic servo system. Kawahara <italic>et al.</italic>
[<xref rid="b8-sensors-14-05207" ref-type="bibr">8</xref>
] developed a system to measure the stiffness of an organ by pushing the organ using air and capturing the deformation using a camera. Peirs <italic>et al.</italic>
[<xref rid="b9-sensors-14-05207" ref-type="bibr">9</xref>
] developed a force sensor that detects the deformation of a flexible structure by using optical fibers. Using fibers leads to issues pertaining to wiring, such as signal distortion resulting from bending, twisting, and chirping. Tada <italic>et al.</italic>
[<xref rid="b10-sensors-14-05207" ref-type="bibr">10</xref>
] developed a force sensor that functions in MRI environments. A point light source is attached to tip of an elastic frame. If a force is applied to the elastic frame, the position of peak illumination changes. By detecting the change via photosensors, the applied forces can be estimated. These sensors are mainly used for laparoscopic surgery, and the size of the parts and the range of measurable forces are different. The part sizes and forces measured for laparoscopic surgery are larger (in the cm and N ranges, respectively) than the corresponding values that would be ideal for endoscopy in neurosurgery (in the mm and mN ranges) Sensors utilizing visualization of force have been developed, although the purpose of such sensors is not medical. Ohka <italic>et al.</italic>
[<xref rid="b11-sensors-14-05207" ref-type="bibr">11</xref>
] have developed a three-axis force sensor by observing the states of conical feelers using a camera. Kamiyama <italic>et al.</italic>
[<xref rid="b12-sensors-14-05207" ref-type="bibr">12</xref>
] have developed a sensor that can measure the direction, magnitude, and distribution of force by observing two layers of spherical markers using a camera. However, to apply these concepts to force sensors in small and thin fiberscopes, the sensor size should be reduced and a method to construct small markers must be developed. In general, this issue is considered to be the disadvantage of sensors utilizing force visualization, as mentioned in previous studies [<xref rid="b5-sensors-14-05207" ref-type="bibr">5</xref>
,<xref rid="b13-sensors-14-05207" ref-type="bibr">13</xref>
]. On the other hand, we previously developed a robotic system with force sensor and feedback systems for neurosurgery [<xref rid="b14-sensors-14-05207" ref-type="bibr">14</xref>
–<xref rid="b16-sensors-14-05207" ref-type="bibr">16</xref>
]. Unfortunately, the developed force sensor was based on a strain gauge system, and as a result, the above issues of sterilization and MRI compatibility were not resolved.</p>
<p>With these issues in mind, this paper presents a novel force sensing system that is attachable to a very thin and commercially available fiberscope (diameter: 1.9 mm) with the goal of realizing force sensing in the deep areas of organs. The main contributions of the developed system are as follows:</p>
<p><italic>Force visualization mechanism utilizing a highly elastic panty stocking fabric</italic>
: We have developed a part that transforms force into deformation of panty stocking fabric (shown in <xref rid="f1-sensors-14-05207" ref-type="fig">Figure 1</xref>
). This fabric is highly elastic and can deform even if the applied force is very small, as will be shown in Sections 3 and 4. Furthermore, this material is thin, inexpensive, and lightweight. The developed part can be attached to a fiberscope, and the deformation of the fabric can be captured using a camera.</p>
<p><italic>High resolution and small size</italic>
: Owing to the high elasticity of the stocking fabric, a high resolution of less than 0.01 N and a sensitivity of greater than 600 pixels/N are realized. The part used for detecting force is very compact, and the diameter of the entire system is less than 4 mm. It does not include electrical parts; therefore, sterilization is simple and MRI-compatibility easy to achieve. In addition, the part can be manufactured at a low cost and is disposable.</p>
<p>In a typical situation, a medical doctor examines the candidate area of a tumor by touching or nudging it with the developed sensor to find the affected area precisely, remove only the affected area, and minimize damage to the surrounding tissues, while observing the area with other endoscopes. In this case, the examination is normally performed by pushing tissues; examinations involving the release of tissues are rare. Therefore, this paper focuses on the case of pushing tissues. The measured force value is displayed on the monitor, superimposed on the image obtained by the endoscope. In this case, the feedback information is shown at the video rate. Therefore, high-sampling-rate data are not always needed, and video rate data are sufficient. Hence, image processing requiring relatively high computational effort can be adopted if the computing time is less than the video rate (10–30 Hz). This paper will thus use an endoscope for sensing force. Other benefits of using the endoscope are as follows. First, if a medical doctor has an endoscope, only the force visualization part is required for constructing a force sensor. Functional extension is then easy and can be done at a low cost. Second, as the endoscope is a conventional medical instrument, approval of the new system will be easy because only the force visualization part will need to be approved. Similarly, the sterilization procedure for the new system should be simple because we only need to consider how to sterilize the force visualization part. Finally, the proposed force sensor should be readily acceptable to medical doctors because it is an extended version of the commonly used endoscope.</p>
<p>The remainder of this paper is organized as follows: first, the structure of the part providing force visualization is presented. Next, the characteristics of the developed part (the relationship between the applied force and the corresponding deformation of the fabric) are evaluated. Subsequently, the method to derive the force value from the captured image is described and the validity of the presented system is shown via experimentation. Finally, the obtained results and outlook are summarized.</p>
</sec>
<sec><label>2.</label>
<title>Structure of the Part Providing Force Visualization by Utilizing Stocking Fabric</title>
<sec><label>2.1.</label>
<title>Basic Principle for Force Sensing</title>
<p>The key to satisfying the requirements of easy sterilization and small size in force sensing is to remove the electronics in the sensor. One solution is force visualization. This involves transforming force into deformation and capturing the deformation as an image. The second requirement is a small range and high resolution. Using neurosurgery as an example, the typical magnitude of force in this application is around 0.1 N [<xref rid="b14-sensors-14-05207" ref-type="bibr">14</xref>
–<xref rid="b16-sensors-14-05207" ref-type="bibr">16</xref>
]. A resolution of less than 0.01 N is then required [<xref rid="b14-sensors-14-05207" ref-type="bibr">14</xref>
–<xref rid="b16-sensors-14-05207" ref-type="bibr">16</xref>
]. The solution for getting such a small range and high resolution is to use highly elastic panty stocking fabric.</p>
<p>In summary, we have developed a force visualization device that utilizes panty stocking fabric, has no electric parts, and is attachable to a fiberscope/endoscope. At the force visualization area, force is transformed into deformation of the high elastic fabric. By deriving the amount of deformation through the captured image, an applied force of small magnitude can be derived with high resolution.</p>
</sec>
<sec><label>2.2.</label>
<title>Basic Structure of Part</title>
<p><xref rid="f2-sensors-14-05207" ref-type="fig">Figure 2a</xref>
shows the basic structure for the force visualization part. Its main parts are a pin, fabric, the fiberscope, and their connecting parts. The pin slides along the depth of the fiberscope (horizontal direction in <xref rid="f2-sensors-14-05207" ref-type="fig">Figure 2a</xref>
). The elastic fabric sits between the pin and the fiberscope. If objects or tissues make contact with the pin, the pin approaches the fiberscope. Because the pin is in contact with the elastic fabric, the distance it moves depends on the magnitude of applied/contact force. Namely, the elastic fabric plays the role of a spring. In the fiberscope, the pin covered with the elastic fabric is observed. <xref rid="f2-sensors-14-05207" ref-type="fig">Figure 2b</xref>
shows an example of the captured image. The circle around the center is the image of the pin with the fabric. If the applied/contact force is large, the radius of the circular image is also large. The magnitude of the applied/contact force can then be derived from the radius of the circular image of the pin.</p>
<p>The designed force visualization part is shown in <xref rid="f3-sensors-14-05207" ref-type="fig">Figure 3a</xref>
. <xref rid="f3-sensors-14-05207" ref-type="fig">Figure 3b</xref>
shows a sectional view of the design. A 20-denier panty stocking fabric is installed at region A in <xref rid="f3-sensors-14-05207" ref-type="fig">Figure 3</xref>
. <xref rid="f3-sensors-14-05207" ref-type="fig">Figure 3c</xref>
shows an overview of the assembly process of the force visualization part, where pins are used for linking the parts. First, part <bold>(IMAGE)</bold>
was linked with part <bold>(IMAGE)</bold>
, whereas part <bold>(IMAGE)</bold>
was linked with part <bold>(IMAGE)</bold>
. Second, part <bold>(IMAGE)</bold>
was connected to the linked part <bold>(IMAGE)</bold>
+<bold>(IMAGE)</bold>
. Lastly, the linked parts <bold>(IMAGE)</bold>
+<bold>(IMAGE)</bold>
and <bold>(IMAGE)</bold>
+<bold>(IMAGE)</bold>
+<bold>(IMAGE)</bold>
were connected. <xref rid="f4-sensors-14-05207" ref-type="fig">Figure 4a</xref>
shows a photograph of the manufactured force visualization part. The material used for the visualization part was duralumin, except for the fabric. <xref rid="f4-sensors-14-05207" ref-type="fig">Figure 4b</xref>
shows the entire system, including where the force visualization part is attached to the fiberscope. The fiberscope used in this paper is a Super Thin Flexible Borescope (MEDIT INC, Winnipeg, Canada). Its diameter is 1.9 mm, its full length is 254 mm, and its visual field is 45°. The camera (Lu 135, Lumenera Corporation, Ottawa, ON, Canada) is connected to the fiberscope. The specifications (measurement conditions) of the camera are listed in <xref rid="t1-sensors-14-05207" ref-type="table">Table 1</xref>
. The image captured using the Lu 135 can be directly sent to a PC via a USB cable. Note that we investigated the effect of distortion when bending the endoscope and found that there was no change of intensity in the captured image.</p>
</sec>
</sec>
<sec><label>3.</label>
<title>Relationship between Applied Force and Moving Distance of Pin</title>
<p>To derive the magnitude of the applied force from the captured image using the radius of the circular image of the pin, we need to know the relationship between the applied force and the moving distance of the pin due to the applied force. This is because the moving distance determines the size of the circular image of the pin. This relationship depends on the used material itself, and if the material changes, the relationship would also change. As such, this relationship is investigated experimentally.</p>
<sec><label>3.1.</label>
<title>Experimental Setup and Procedure</title>
<p><xref rid="f5-sensors-14-05207" ref-type="fig">Figure 5</xref>
shows the experimental setup for the investigation. A force is applied by a force gauge (ZP-5N, IMADA, Toyohashi, Aichi, Japan, resolution: 0.001 N) attached to an automatic positioning stage (ELSM2YF030-KD-C, Oriental Motor, Tokyo, Japan, movement speed: 100 mm/s). A pin with a diameter of 1.9 mm is attached to the tip of the force gauge. This pin is used for pushing the force visualization part attached to the fiberscope. The fiberscope is fixed to a custom-made stage so that the direction of pushing can be controlled appropriately. The position and orientation of the two pins attached to the force gauge and the fiberscope are set up such that their position and orientation are the same.</p>
<p>Because cases involving tissue release are rare, as mentioned above, we focus on the case of pushing tissues. The first step in the experiment was to set up the initial state such that the value shown by the force gauge is 0.000 N while both pins are in contact with each other. Then, the automatic positioning stage was moved in steps of 0.2 mm to push the pin attached to the fiberscope until the total distance moved reached 2.0 mm. At each step, the applied force was measured by the force gauge. This procedure was repeated five times.</p>
</sec>
<sec><label>3.2.</label>
<title>Relationship between Applied Force and Pin Movement</title>
<p><xref rid="f6-sensors-14-05207" ref-type="fig">Figure 6</xref>
shows the experimental results for the relationship between the applied force and the moving distance of the pin from the initial state. The diamond symbols indicate the results when the pin is pushing. The error bars show the standard deviation. A regression analysis was performed using second-order polynomial function:
<disp-formula id="FD1"><label>(1)</label>
<mml:math id="mm1"><mml:mrow><mml:mi>F</mml:mi>
<mml:mo>=</mml:mo>
<mml:mi>a</mml:mi>
<mml:msup><mml:mi>D</mml:mi>
<mml:mn>2</mml:mn>
</mml:msup>
<mml:mo>+</mml:mo>
<mml:mi>b</mml:mi>
<mml:mi>D</mml:mi>
</mml:mrow>
</mml:math>
</disp-formula>
where <italic>a</italic>
= 4.6 × 10<sup>−2</sup>
and <italic>b</italic>
= 4.7 × 10<sup>−2</sup>
. The coefficients of determination were 0.99. It can be seen that the fitted curve expresses the relationships very well.</p>
<p>The used (knitted) fabric has a reticular pattern and is manufactured using multiple (bended and twisted) strings. If the load is low, the deformation of the fabric is mainly caused by stretching the bended strings. The relationship between load and displacement can then be expressed by a nonlinear function [<xref rid="b17-sensors-14-05207" ref-type="bibr">17</xref>
,<xref rid="b18-sensors-14-05207" ref-type="bibr">18</xref>
]. If the load is large, the stings are stretched, and the deformation is then dominated by the stiffness of the stings themselves. In this case, the relationship between load and displacement can be expressed using a linear function. In our case, the maximum value of the applied force was roughly 0.3 N and the load was assumed to be low. In this case, a nonlinear function should be chosen for regression. This is why we used a second-order polynomial function.</p>
</sec>
</sec>
<sec><label>4.</label>
<title>Methodology for Derivation of Force Value from a Captured Image</title>
<p>In this section, the methodology for deriving the magnitude of the applied force from the captured image is described. First, the circular area corresponding to the area of the pin within the elastic fabric is extracted. The magnitude of the applied force is then derived from the radius of the circular area.</p>
<sec><label>4.1.</label>
<title>Extraction of Circular Image of Pin</title>
<p><xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7</xref>
shows the procedure and corresponding image at each step. <xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7a</xref>
shows the original captured image. The area surrounded by the relatively dark area is the area of the pin with the elastic fabric. We took the following steps for extracting circular area corresponding to the pin area:
<list list-type="simple"><list-item><label>➀</label>
<p>Smoothing and edge enhancement: To reduce noise and to clarify the boundary of the pin area, smoothing and edge enhancement are performed. <xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7b</xref>
shows the obtained image.</p>
</list-item>
<list-item><label>➁</label>
<p>Converting to a grayscale image: As a preprocessing step for binarization, the (color; image is converted to a grayscale image. The obtained image is shown in <xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7c</xref>
.</p>
</list-item>
<list-item><label>➂</label>
<p>Binarizing and selecting area: To obtain information regarding the radius of the pin area, we binarize the grayscale image. We determine the pin area in the obtained binarized image by searching the area that has the maximum area. <xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7d</xref>
shows the obtained image.</p>
</list-item>
<list-item><label>➃</label>
<p>Extracting circular area: The largest area (corresponding to the area of the pin with the elastic fabric) is detected, and we derive the minimum circular area including the largest detected area (pin area;. The obtained circular area is shown in <xref rid="f7-sensors-14-05207" ref-type="fig">Figure 7e</xref>
. Hereafter, we call this circular area the circular pin image. Finally, we derive the radius of the obtained circular area (circular pin image).</p>
</list-item>
</list>
</p>
<p>We implemented these processing steps with Halcon (MVTech, Munich, Germany). The computing time is less than 90 ms, and 10 ms without the smoothing procedure. If the processing time in Halcon is less than in conventional C++ programing code, the computing time is considered to be fast enough to display the force information on the monitor (visual image) in real time.</p>
</sec>
<sec><label>4.2.</label>
<title>Deviation of Magnitude of Force</title>
<p>To obtain the relationship between the applied force and the area of the radius of the circular pin image, we consider the relationship between the object area in the image and the actual location of the object. Consider the case shown in <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8a</xref>
where a spherical object with radius, <italic>R</italic>
, is captured by a camera. We compare the cases when the distance between the object and the camera is <italic>D</italic>
<sub>0</sub>
and <italic>D</italic>
<sub>0</sub>
-<italic>D. W</italic>
<sub>0</sub>
and <italic>W</italic>
denote the actual length corresponding to the width (<italic>w</italic>
) in the image captured by the camera when the distance is <italic>D</italic>
<sub>0</sub>
and <italic>D</italic>
<sub>0</sub>
-<italic>D</italic>
, respectively. <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8b</xref>
shows the image captured by the camera in <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8a</xref>
. The left panel of <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8b</xref>
shows the case when the object is located at a distance <italic>D</italic>
<sub>0</sub>
(corresponding to A in <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8a</xref>
). The right panel of <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8b</xref>
shows the case where the object is located at a distance <italic>D</italic>
<sub>0</sub>
-<italic>D</italic>
(corresponding to B in <xref rid="f8-sensors-14-05207" ref-type="fig">Figure 8a</xref>
). <italic>r</italic>
<sub>0</sub>
and <italic>r</italic>
are the apparent radii of the spherical object with a radius of <italic>R</italic>
in the captured image.</p>
<p><disp-formula id="FD2"><label>(2)</label>
<mml:math id="mm2"><mml:mrow><mml:mfrac><mml:mrow><mml:msub><mml:mi>r</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
</mml:mrow>
<mml:mi>r</mml:mi>
</mml:mfrac>
<mml:mo>=</mml:mo>
<mml:mfrac><mml:mrow><mml:msub><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
<mml:mo>−</mml:mo>
<mml:mi>D</mml:mi>
</mml:mrow>
<mml:mrow><mml:msub><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
</mml:mrow>
</mml:mfrac>
</mml:mrow>
</mml:math>
</disp-formula>
</p>
<p>On the other hand, the relationship between pin movement and applied force is given in <xref rid="FD1" ref-type="disp-formula">Equation (1)</xref>
. By substituting <xref rid="FD2" ref-type="disp-formula">Equation (2)</xref>
into <xref rid="FD1" ref-type="disp-formula">Equation (1)</xref>
, the following relationship is obtained:
<disp-formula id="FD3"><label>(3)</label>
<mml:math id="mm3"><mml:mrow><mml:mi>F</mml:mi>
<mml:mo>=</mml:mo>
<mml:mi>α</mml:mi>
<mml:msup><mml:mrow><mml:mrow><mml:mo>(</mml:mo>
<mml:mrow><mml:mfrac><mml:mn>1</mml:mn>
<mml:mi>r</mml:mi>
</mml:mfrac>
</mml:mrow>
<mml:mo>)</mml:mo>
</mml:mrow>
</mml:mrow>
<mml:mn>2</mml:mn>
</mml:msup>
<mml:mo>+</mml:mo>
<mml:mi>β</mml:mi>
<mml:mrow><mml:mo>(</mml:mo>
<mml:mrow><mml:mfrac><mml:mn>1</mml:mn>
<mml:mi>r</mml:mi>
</mml:mfrac>
</mml:mrow>
<mml:mo>)</mml:mo>
</mml:mrow>
<mml:mo>+</mml:mo>
<mml:mi>γ</mml:mi>
</mml:mrow>
</mml:math>
</disp-formula>
where:
<disp-formula id="FD4"><label>(4)</label>
<mml:math id="mm4"><mml:mrow><mml:mtable><mml:mtr><mml:mtd><mml:mrow><mml:mi>α</mml:mi>
<mml:mo>=</mml:mo>
<mml:mi>a</mml:mi>
<mml:msubsup><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
<mml:mn>2</mml:mn>
</mml:msubsup>
<mml:msubsup><mml:mi>r</mml:mi>
<mml:mn>0</mml:mn>
<mml:mn>2</mml:mn>
</mml:msubsup>
</mml:mrow>
</mml:mtd>
</mml:mtr>
<mml:mtr><mml:mtd><mml:mrow><mml:mi>β</mml:mi>
<mml:mo>=</mml:mo>
<mml:mo>−</mml:mo>
<mml:mo stretchy="false">(</mml:mo>
<mml:mn>2</mml:mn>
<mml:mi>a</mml:mi>
<mml:msubsup><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
<mml:mn>2</mml:mn>
</mml:msubsup>
<mml:msubsup><mml:mi>r</mml:mi>
<mml:mn>0</mml:mn>
<mml:mn>2</mml:mn>
</mml:msubsup>
<mml:mo>+</mml:mo>
<mml:mi>b</mml:mi>
<mml:msub><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
<mml:msub><mml:mi>r</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
<mml:mo stretchy="false">)</mml:mo>
</mml:mrow>
</mml:mtd>
</mml:mtr>
<mml:mtr><mml:mtd><mml:mrow><mml:mi>γ</mml:mi>
<mml:mo>=</mml:mo>
<mml:mi>a</mml:mi>
<mml:msubsup><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
<mml:mn>2</mml:mn>
</mml:msubsup>
<mml:mo>+</mml:mo>
<mml:mi>b</mml:mi>
<mml:msub><mml:mi>D</mml:mi>
<mml:mn>0</mml:mn>
</mml:msub>
</mml:mrow>
</mml:mtd>
</mml:mtr>
</mml:mtable>
</mml:mrow>
</mml:math>
</disp-formula>
</p>
<p>From <xref rid="FD2" ref-type="disp-formula">Equation (2)</xref>
, it can be seen that the magnitude of the applied force can be expressed using a second-order polynomial function with respect to the inverse of the radius of the obtained circular pin image.</p>
</sec>
</sec>
<sec><label>5.</label>
<title>Experiment</title>
<p>By performing an experiment for investigating the relationship between the applied force and the radius of the circular pin image, we demonstrate the validity of our approach. In neurosurgery, most of the organs are normally in a steady state. Therefore, we conducted experiments where the target does not move.</p>
<p>The experimental setup is the same as that described in Section 3.1. The procedure is as follows. First, we set up an initial state where the value of the force gauge is 0.000 N while both pins are in contact with each other. Then, the automatic positioning stage, used to push the pin attached to the fiberscope, is moved in steps of 0.02 N. Note that the step size was based upon the magnitude of the applied force. The magnitude was controlled using the automatic positioning stage with a resolution of 0.01 mm, confirming the force value measured by the force gauge. In addition, note that the camera can only catch light from the light source shown in <xref rid="f6-sensors-14-05207" ref-type="fig">Figure 6</xref>
. This experiment was repeated five times.</p>
<p><xref rid="f9-sensors-14-05207" ref-type="fig">Figure 9a</xref>
shows the captured image. The area of the pin increases with the increase in applied force. <xref rid="f9-sensors-14-05207" ref-type="fig">Figure 9b</xref>
shows the corresponding circular pin image obtained through the image processing method described in Section 4.1. As described in the previous section, the magnitude of the applied force can be represented by a second-order polynomial function with respect to the inverse of the radius. We can then approximate the relationship with the equation given in <xref rid="FD2" ref-type="disp-formula">Equation (2)</xref>
:
<disp-formula id="FD5"><label>(5)</label>
<mml:math id="mm5"><mml:mrow><mml:mi>F</mml:mi>
<mml:mo>=</mml:mo>
<mml:mn>1.06</mml:mn>
<mml:mo>×</mml:mo>
<mml:msup><mml:mrow><mml:mn>10</mml:mn>
</mml:mrow>
<mml:mn>4</mml:mn>
</mml:msup>
<mml:msup><mml:mrow><mml:mrow><mml:mo>(</mml:mo>
<mml:mrow><mml:mfrac><mml:mn>1</mml:mn>
<mml:mi>r</mml:mi>
</mml:mfrac>
</mml:mrow>
<mml:mo>)</mml:mo>
</mml:mrow>
</mml:mrow>
<mml:mn>2</mml:mn>
</mml:msup>
<mml:mo>−</mml:mo>
<mml:mn>2.10</mml:mn>
<mml:mo>×</mml:mo>
<mml:msup><mml:mrow><mml:mn>10</mml:mn>
</mml:mrow>
<mml:mn>2</mml:mn>
</mml:msup>
<mml:mrow><mml:mo>(</mml:mo>
<mml:mrow><mml:mfrac><mml:mn>1</mml:mn>
<mml:mi>r</mml:mi>
</mml:mfrac>
</mml:mrow>
<mml:mo>)</mml:mo>
</mml:mrow>
<mml:mo>+</mml:mo>
<mml:mn>1.05</mml:mn>
</mml:mrow>
</mml:math>
</disp-formula>
</p>
<p><xref rid="f10-sensors-14-05207" ref-type="fig">Figure 10</xref>
shows the obtained relationship between the applied force and the inverse of the radius of the circular pin image with the obtained fitted curve. The coefficient of determination was 0.99, and the fitted curve accurately represents the relationship. The range of the applied force ranged from 0 to 0.2 N, and the force applied to the elastic fabric was assumed to be small. Therefore, the function given in <xref rid="FD4" ref-type="disp-formula">Equation (4)</xref>
accurately represented the relationship, and a high coefficient of determination was obtained.</p>
<p>Because the relationship given in <xref rid="FD4" ref-type="disp-formula">Equation (4)</xref>
is nonlinear, the resolution and sensitivity vary with the range. For sensitivity analysis, <italic>d</italic>
(2<italic>r</italic>
)/<italic>df</italic>
was calculated based on <xref rid="FD4" ref-type="disp-formula">Equation (4)</xref>
. Because the minimum amount of change in <italic>r</italic>
(radius of the circular pin image) is 0.5 pixels, not <italic>dr</italic>
)/<italic>df</italic>
but rather <italic>d</italic>
(2<italic>r</italic>
)/<italic>df</italic>
was calculated (2<italic>r</italic>
corresponds to the diameter of the circular pin image). <xref rid="f11-sensors-14-05207" ref-type="fig">Figure 11</xref>
shows the obtained relationship between the sensitivity <italic>d</italic>
(2<italic>r</italic>
)/<italic>df</italic>
and applied force. It can be seen that the sensitively is slightly larger than 600 pixels/N when the applied force exceeds 0.05 N, while the sensitivity is very high when the applied force is less than 0.05 N. The sensitivity always exceeded 600 pixels/N, which means one pixel corresponds to 0.0017 N. This minimal value (600 pixels/N) is considered to be the sensitivity of the developed sensor system. It is considered to represent high sensitivity.</p>
<p>From <xref rid="f11-sensors-14-05207" ref-type="fig">Figure 11</xref>
and <xref rid="FD4" ref-type="disp-formula">Equation (4)</xref>
, the sensitivity is minimal at around 0.12–0.13 N. Therefore, we focused on this area to examine the resolution. We measured the radius of the circular pin image for a case of 0.12 N and 0.13 N five times. These results are shown in <xref rid="f12-sensors-14-05207" ref-type="fig">Figure 12</xref>
. A <italic>t</italic>
-test was applied, and a value of <italic>p</italic>
≪ 0.005 was obtained. This shows that there is a statistically significant difference between the cases of 0.12 N and 0.13 N. This indicates that the resolution is at least less than 0.01 N.</p>
</sec>
<sec sec-type="conclusions"><label>6.</label>
<title>Conclusions</title>
<p>This paper presents a novel force sensing system that can be used with a thin and small fiberscope/endoscope. We developed a part that transforms force into deformation of a highly elastic fabric. The developed part can be attached to the fiberscope/endoscope, and the deformation can be captured using a camera. By visualizing the force, we eliminated the need for using electrical parts for force sensing. This design also has the advantages of easy sterilization, small size, and low cost. We also described the methods used to derive the magnitude of the applied force from the captured image. We also showed that the force can be measured with high resolution (less than 0.01 N) and high sensitivity (greater than 600 pixels/N).</p>
<p>The goal of developing the system is to enable medical investigation of tissues located in areas deep within organs. By attaching the developed part to a fiberscope, force information can be obtained when visual information might however still be difficult to acquire. A solution to this problem is to use two fiberscopes. One fiberscope is used for force information, whereas the other is used for visual information.</p>
<p>Although the circular pin image can be used for force feedback information, intuitively estimating the force value is difficult owing to the nonlinearity. Future directions in this area could involve the development of an appropriate force feedback system. The presented force sensor can measure forces in only one direction. In situations requiring examinations that involve the release of tissues, hysteresis may need to be considered [<xref rid="b19-sensors-14-05207" ref-type="bibr">19</xref>
]. We did not check whether the device was waterproof, or consider the measurement of dynamic forces. These issues will also be addressed in future research.</p>
</sec>
</body>
<back><ack><p>This work was supported by Nakatani Foundation for Advancement of Measuring Technologies in Biomedical Engineering and JKA. The authors would also like to thank Mr. Norifumi Sugiyama for helping to conduct experiments and analyses.</p>
</ack>
<notes><title>Author Contributions</title>
<p>All the authors have contributed to ensure and improve the quality of this work. Tetsuyou Watanabe presented the basic concept of the developed sensor and wrote the main part of this paper. Takanobu Iwai realized and analyzed the sensor system.</p>
</notes>
<notes><title>Conflicts of Interest</title>
<p>The authors declare no conflict of interest.</p>
</notes>
<ref-list><title>References</title>
<ref id="b1-sensors-14-05207"><label>1.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Puangmali</surname>
<given-names>P.</given-names>
</name>
<name><surname>Althoefer</surname>
<given-names>K.</given-names>
</name>
<name><surname>Seneviratne</surname>
<given-names>D.</given-names>
</name>
<name><surname>Murphy</surname>
<given-names>D.</given-names>
</name>
<name><surname>Dasgupta</surname>
<given-names>P.</given-names>
</name>
</person-group>
<article-title>State-of-the-art in force and tactile sensing for minimally invasive surgery</article-title>
<source>Sens. J.</source>
<year>2008</year>
<volume>8</volume>
<fpage>371</fpage>
<lpage>381</lpage>
</element-citation>
</ref>
<ref id="b2-sensors-14-05207"><label>2.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Westebring-van der Putten</surname>
<given-names>E.</given-names>
</name>
<name><surname>Goossens</surname>
<given-names>R.</given-names>
</name>
<name><surname>Jakimowicz</surname>
<given-names>J.</given-names>
</name>
<name><surname>Dankelman</surname>
<given-names>J.</given-names>
</name>
</person-group>
<article-title>Haptics in minimally invasive surgery-a review</article-title>
<source>Minim. Invasive Ther. Allied Technol.</source>
<year>2008</year>
<volume>17</volume>
<fpage>3</fpage>
<lpage>16</lpage>
<pub-id pub-id-type="pmid">18270873</pub-id>
</element-citation>
</ref>
<ref id="b3-sensors-14-05207"><label>3.</label>
<element-citation publication-type="book"><person-group person-group-type="author"><name><surname>Okamura</surname>
<given-names>A.</given-names>
</name>
<name><surname>Verner</surname>
<given-names>C.</given-names>
</name>
<name><surname>Mahvash</surname>
<given-names>M.</given-names>
</name>
</person-group>
<article-title>Haptics for robotassisted minimally invasive surgery</article-title>
<source>Robotics Research</source>
<publisher-name>Springer</publisher-name>
<publisher-loc>Berlin/Heidelberg, Germany</publisher-loc>
<year>2011</year>
<fpage>361</fpage>
<lpage>372</lpage>
</element-citation>
</ref>
<ref id="b4-sensors-14-05207"><label>4.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Poorten</surname>
<given-names>V.E.</given-names>
</name>
<name><surname>Demeester</surname>
<given-names>E.</given-names>
</name>
<name><surname>Lammertse</surname>
<given-names>P.</given-names>
</name>
</person-group>
<article-title>Haptic feedback for medical applications, a survey</article-title>
<source>Proc. Actuator</source>
<year>2012</year>
<fpage>18</fpage>
<lpage>20</lpage>
</element-citation>
</ref>
<ref id="b5-sensors-14-05207"><label>5.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Tiwana</surname>
<given-names>M.I.</given-names>
</name>
<name><surname>Redmond</surname>
<given-names>S.J.</given-names>
</name>
<name><surname>Lovell</surname>
<given-names>N.H.</given-names>
</name>
</person-group>
<article-title>A review of tactile sensing technologies with applications in biomedical engineering</article-title>
<source>Sens. Actuator A</source>
<year>2012</year>
<volume>179</volume>
<fpage>17</fpage>
<lpage>31</lpage>
</element-citation>
</ref>
<ref id="b6-sensors-14-05207"><label>6.</label>
<element-citation publication-type="confproc"><person-group person-group-type="author"><name><surname>Takaki</surname>
<given-names>T.</given-names>
</name>
<name><surname>Omasa</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Ishii</surname>
<given-names>I.</given-names>
</name>
<name><surname>Kawahara</surname>
<given-names>T.</given-names>
</name>
<name><surname>Okajima</surname>
<given-names>M.</given-names>
</name>
</person-group>
<article-title>Force Visualization Mechanism Using a Moire Fringe Applied to Endoscopic Surgical Instruments</article-title>
<conf-name>Proceedings of the IEEE International Conference on Robotics and Automation</conf-name>
<conf-loc>Anchorage, AK, USA</conf-loc>
<conf-date>3–7 May 2010</conf-date>
<fpage>3648</fpage>
<lpage>3653</lpage>
</element-citation>
</ref>
<ref id="b7-sensors-14-05207"><label>7.</label>
<element-citation publication-type="confproc"><person-group person-group-type="author"><name><surname>Tadano</surname>
<given-names>K.</given-names>
</name>
<name><surname>Kawashima</surname>
<given-names>K.</given-names>
</name>
</person-group>
<article-title>Development of 4-Dofs Forceps with Force Sensing Using Pneumatic Servo System</article-title>
<conf-name>Proceedings of the IEEE International Conference on Robotics and Automation</conf-name>
<conf-loc>Orlando, FL, USA</conf-loc>
<conf-date>15–19 May 2006</conf-date>
<fpage>2250</fpage>
<lpage>2255</lpage>
</element-citation>
</ref>
<ref id="b8-sensors-14-05207"><label>8.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Kawahara</surname>
<given-names>T.</given-names>
</name>
<name><surname>Tanaka</surname>
<given-names>S.</given-names>
</name>
<name><surname>Kaneko</surname>
<given-names>M.</given-names>
</name>
</person-group>
<article-title>Non-contact stiffness imager</article-title>
<source>Int. J. Robot. Res.</source>
<year>2006</year>
<volume>25</volume>
<fpage>537</fpage>
<lpage>549</lpage>
</element-citation>
</ref>
<ref id="b9-sensors-14-05207"><label>9.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Peirs</surname>
<given-names>J.</given-names>
</name>
<name><surname>Clijnen</surname>
<given-names>J.</given-names>
</name>
<name><surname>Reynaerts</surname>
<given-names>D.</given-names>
</name>
<name><surname>Brussel</surname>
<given-names>H.V.</given-names>
</name>
<name><surname>Herijgers</surname>
<given-names>P.</given-names>
</name>
<name><surname>Corteville</surname>
<given-names>B.</given-names>
</name>
<name><surname>Boone</surname>
<given-names>S.</given-names>
</name>
</person-group>
<article-title>A micro optical force sensor for force feedback during minimally invasive robotic surgery</article-title>
<source>Sens. Actuator A</source>
<year>2004</year>
<volume>115</volume>
<fpage>447</fpage>
<lpage>455</lpage>
</element-citation>
</ref>
<ref id="b10-sensors-14-05207"><label>10.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Tada</surname>
<given-names>M.</given-names>
</name>
<name><surname>Sasaki</surname>
<given-names>S.</given-names>
</name>
<name><surname>Ogasawara</surname>
<given-names>T.</given-names>
</name>
</person-group>
<article-title>Development of an optical 2-axis force sensor usable in MRI environments</article-title>
<source>IEEE Sens.</source>
<year>2002</year>
<volume>2</volume>
<fpage>984</fpage>
<lpage>989</lpage>
</element-citation>
</ref>
<ref id="b11-sensors-14-05207"><label>11.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Ohka</surname>
<given-names>M.</given-names>
</name>
<name><surname>Mitsuya</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Matsunaga</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Takeuchi</surname>
<given-names>S.</given-names>
</name>
</person-group>
<article-title>Sensing characteristics of an optical three-axis tactile sensor under combined loading</article-title>
<source>Robotica</source>
<year>2004</year>
<volume>22</volume>
<fpage>213</fpage>
<lpage>221</lpage>
</element-citation>
</ref>
<ref id="b12-sensors-14-05207"><label>12.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Kamiyama</surname>
<given-names>K.</given-names>
</name>
<name><surname>Vlack</surname>
<given-names>K.</given-names>
</name>
<name><surname>Mizota</surname>
<given-names>T.</given-names>
</name>
<name><surname>Kajimoto</surname>
<given-names>H.</given-names>
</name>
<name><surname>Kawakami</surname>
<given-names>N.</given-names>
</name>
<name><surname>Tachi</surname>
<given-names>S.</given-names>
</name>
</person-group>
<article-title>Vision-based sensor for real-time measuring of surface traction fields</article-title>
<source>IEEE Comput. Graph. Appl.</source>
<year>2005</year>
<volume>25</volume>
<fpage>68</fpage>
<lpage>75</lpage>
<pub-id pub-id-type="pmid">15691175</pub-id>
</element-citation>
</ref>
<ref id="b13-sensors-14-05207"><label>13.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Dahiya</surname>
<given-names>R.S.</given-names>
</name>
<name><surname>Metta</surname>
<given-names>G.</given-names>
</name>
<name><surname>Valle</surname>
<given-names>M.</given-names>
</name>
<name><surname>Sandini</surname>
<given-names>G.</given-names>
</name>
</person-group>
<article-title>Tactile Sensing—From Humans to Humanoids</article-title>
<source>IEEE Trans. Robot.</source>
<year>2010</year>
<volume>6</volume>
<fpage>1</fpage>
<lpage>20</lpage>
</element-citation>
</ref>
<ref id="b14-sensors-14-05207"><label>14.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Yoneyama</surname>
<given-names>T.</given-names>
</name>
<name><surname>Watanabe</surname>
<given-names>T.</given-names>
</name>
<name><surname>Kagawa</surname>
<given-names>H.</given-names>
</name>
<name><surname>Hamada</surname>
<given-names>J.</given-names>
</name>
<name><surname>Hayashi</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Nakada</surname>
<given-names>M.</given-names>
</name>
</person-group>
<article-title>Force-detecting gripper and force feedback system for neurosurgery applications</article-title>
<source>Int. J. Comput. Assist. Radiol. Surg.</source>
<year>2013</year>
<volume>8</volume>
<fpage>819</fpage>
<lpage>829</lpage>
<pub-id pub-id-type="pmid">23315003</pub-id>
</element-citation>
</ref>
<ref id="b15-sensors-14-05207"><label>15.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Kanada</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Yoneyama</surname>
<given-names>T.</given-names>
</name>
<name><surname>Watanabe</surname>
<given-names>T.</given-names>
</name>
<name><surname>Kagawa</surname>
<given-names>H.</given-names>
</name>
<name><surname>Sugiyama</surname>
<given-names>N.</given-names>
</name>
<name><surname>Tanaka</surname>
<given-names>K.</given-names>
</name>
<name><surname>Hanyu</surname>
<given-names>T.</given-names>
</name>
</person-group>
<article-title>Force feedback manipulating system for neurosurgery</article-title>
<source>Proc. CIRP</source>
<year>2013</year>
<volume>5</volume>
<fpage>133</fpage>
<lpage>136</lpage>
</element-citation>
</ref>
<ref id="b16-sensors-14-05207"><label>16.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Fujihira</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Hanyu</surname>
<given-names>T.</given-names>
</name>
<name><surname>Kanada</surname>
<given-names>Y.</given-names>
</name>
<name><surname>Yoneyama</surname>
<given-names>T.</given-names>
</name>
<name><surname>Watanabe</surname>
<given-names>T.</given-names>
</name>
<name><surname>Kagawa</surname>
<given-names>H.</given-names>
</name>
</person-group>
<article-title>Gripping Force Feedback System for Neurosurgery</article-title>
<source>Int. J. Autom. Technol.</source>
<year>2014</year>
<volume>8</volume>
<fpage>83</fpage>
<lpage>94</lpage>
</element-citation>
</ref>
<ref id="b17-sensors-14-05207"><label>17.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Kawabata</surname>
<given-names>S.</given-names>
</name>
</person-group>
<article-title>“Linearizing Method” for Solving Non-linear Biaxial Tensile Property of fabric</article-title>
<source>J. Text. Mach. Soc. Jpn.</source>
<year>1986</year>
<volume>39</volume>
<fpage>T169</fpage>
<lpage>T173</lpage>
</element-citation>
</ref>
<ref id="b18-sensors-14-05207"><label>18.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Kawabata</surname>
<given-names>S. A</given-names>
</name>
</person-group>
<article-title>Method of Theoretical Calculation of Tensile Properties of Knitted Fabric from its Structure and Yarn Properties</article-title>
<source>J. Text. Mach. Soc. Jpn.</source>
<year>1970</year>
<volume>23</volume>
<fpage>T30</fpage>
<lpage>T34</lpage>
</element-citation>
</ref>
<ref id="b19-sensors-14-05207"><label>19.</label>
<element-citation publication-type="journal"><person-group person-group-type="author"><name><surname>Sánchez-Durán</surname>
<given-names>J.A.</given-names>
</name>
<name><surname>Oballe-Peinado</surname>
<given-names>Ó.</given-names>
</name>
<name><surname>Castellanos-Ramos</surname>
<given-names>J.</given-names>
</name>
<name><surname>Vidal-Verdú</surname>
<given-names>F.</given-names>
</name>
</person-group>
<article-title>Hysteresis correction of tactile sensor response with a generalized Prandtl–Ishlinskii model</article-title>
<source>Microsyst. Technol.</source>
<year>2012</year>
<volume>18</volume>
<fpage>1127</fpage>
<lpage>1138</lpage>
</element-citation>
</ref>
</ref-list>
</back>
<floats-group><fig id="f1-sensors-14-05207" position="float"><label>Figure 1.</label>
<caption><p>Panty stocking fabric.</p>
</caption>
<graphic xlink:href="sensors-14-05207f1"></graphic>
</fig>
<fig id="f2-sensors-14-05207" position="float"><label>Figure 2.</label>
<caption><p>(<bold>a</bold>
) Schematic structure of force visualization part. (<bold>b</bold>
) Captured image of pin (with elastic fabric).</p>
</caption>
<graphic xlink:href="sensors-14-05207f2"></graphic>
</fig>
<fig id="f3-sensors-14-05207" position="float"><label>Figure 3.</label>
<caption><p>(<bold>a</bold>
) Design of force visualization part: three-dimensional view (<bold>b</bold>
) Design of force visualization part: sectional view (<bold>c</bold>
) Overview of assembly process.</p>
</caption>
<graphic xlink:href="sensors-14-05207f3"></graphic>
</fig>
<fig id="f4-sensors-14-05207" position="float"><label>Figure 4.</label>
<caption><p>(<bold>a</bold>
) Photograph of manufactured force visualization part (<bold>b</bold>
) Complete view of developed force sensing system.</p>
</caption>
<graphic xlink:href="sensors-14-05207f4"></graphic>
</fig>
<fig id="f5-sensors-14-05207" position="float"><label>Figure 5.</label>
<caption><p>(<bold>a</bold>
) Picture of experimental setup (<bold>b</bold>
) Image of experimental setup.</p>
</caption>
<graphic xlink:href="sensors-14-05207f5"></graphic>
</fig>
<fig id="f6-sensors-14-05207" position="float"><label>Figure 6.</label>
<caption><p>Relationship between applied force and moving distance of pin. Error bars show standard deviation. Note that they are too small to see in some cases.</p>
</caption>
<graphic xlink:href="sensors-14-05207f6"></graphic>
</fig>
<fig id="f7-sensors-14-05207" position="float"><label>Figure 7.</label>
<caption><p>(<bold>a</bold>
) Original image (<bold>b</bold>
) Smoothing and edge enhancement (<bold>c</bold>
) Grayscale image <bold>(d)</bold>
Binarizing and selecting area <bold>(e)</bold>
Obtained circular area of pin.</p>
</caption>
<graphic xlink:href="sensors-14-05207f7"></graphic>
</fig>
<fig id="f8-sensors-14-05207" position="float"><label>Figure 8.</label>
<caption><p>(<bold>a</bold>
) Size of object area depends on its location. The object area at location B is larger than that at location A in the image captured by the camera. (<bold>b</bold>
) Image captured by the camera when object is located at A (left) and object is located at B (right).</p>
</caption>
<graphic xlink:href="sensors-14-05207f8"></graphic>
</fig>
<fig id="f9-sensors-14-05207" position="float"><label>Figure 9.</label>
<caption><p>(<bold>a</bold>
) Image captured by camera attached to fiberscope. (<bold>b</bold>
) Circular pin image.</p>
</caption>
<graphic xlink:href="sensors-14-05207f9"></graphic>
</fig>
<fig id="f10-sensors-14-05207" position="float"><label>Figure 10.</label>
<caption><p>Relationship between applied force and inverse of radius of circular image of pin.</p>
</caption>
<graphic xlink:href="sensors-14-05207f10"></graphic>
</fig>
<fig id="f11-sensors-14-05207" position="float"><label>Figure 11.</label>
<caption><p>Relationship between sensitivity <italic>d</italic>
(2<italic>r</italic>
)/<italic>df</italic>
and applied force.</p>
</caption>
<graphic xlink:href="sensors-14-05207f11"></graphic>
</fig>
<fig id="f12-sensors-14-05207" position="float"><label>Figure 12.</label>
<caption><p>Radius of circular image of pin for 0.12 N and 0.13 N measured five times. Error bars show maximum differences.</p>
</caption>
<graphic xlink:href="sensors-14-05207f12"></graphic>
</fig>
<table-wrap id="t1-sensors-14-05207" position="float"><label>Table 1.</label>
<caption><p>Specifications of Lumenera Lu 135 Camera.</p>
</caption>
<table frame="hsides" rules="groups"><tbody><tr><td align="center" valign="bottom" rowspan="1" colspan="1"><bold>Size of Image</bold>
</td>
<td align="center" valign="bottom" rowspan="1" colspan="1">1,392 × 1,040</td>
</tr>
<tr><td align="center" valign="bottom" rowspan="1" colspan="1"><bold>Frame Rate</bold>
</td>
<td align="center" valign="bottom" rowspan="1" colspan="1">15 fps</td>
</tr>
<tr><td align="center" valign="bottom" rowspan="1" colspan="1"><bold>Exposure Time</bold>
</td>
<td align="center" valign="bottom" rowspan="1" colspan="1">66 ms</td>
</tr>
<tr><td align="center" valign="bottom" rowspan="1" colspan="1"><bold>Whole Gain</bold>
</td>
<td align="center" valign="bottom" rowspan="1" colspan="1">2.0 dB</td>
</tr>
</tbody>
</table>
</table-wrap>
</floats-group>
</pmc>
</record>
Pour manipuler ce document sous Unix (Dilib)
EXPLOR_STEP=$WICRI_ROOT/Ticri/CIDE/explor/HapticV1/Data/Pmc/Curation
HfdSelect -h $EXPLOR_STEP/biblio.hfd -nk 002475 | SxmlIndent | more
Ou
HfdSelect -h $EXPLOR_AREA/Data/Pmc/Curation/biblio.hfd -nk 002475 | SxmlIndent | more
Pour mettre un lien sur cette page dans le réseau Wicri
{{Explor lien |wiki= Ticri/CIDE |area= HapticV1 |flux= Pmc |étape= Curation |type= RBID |clé= PMC:4003989 |texte= Force Sensor Attachable to Thin Fiberscopes/Endoscopes Utilizing High Elasticity Fabric }}
Pour générer des pages wiki
HfdIndexSelect -h $EXPLOR_AREA/Data/Pmc/Curation/RBID.i -Sk "pubmed:24625744" \ | HfdSelect -Kh $EXPLOR_AREA/Data/Pmc/Curation/biblio.hfd \ | NlmPubMed2Wicri -a HapticV1
![]() | This area was generated with Dilib version V0.6.23. | ![]() |